Search
Advanced search
Filter by category
Filter by committee
Search results
-
ASTM International’s particle and spray characterization committee ( E29 ) is developing a proposed standard that will be used to measure physical and chemical properties of nanoparticles in a variety of industrial realms. The standard ( E3427 ) describes how to use laser-amplified detection/power spectrum analysis to measure the number of physical and chemical properties of nanoparticles,…, Media Inquiries:, Gavin O’Reilly, tel +1.610.832.9618; goreilly@astm.org, Committee Contact:, Jennifer Tursi, tel +1.610.832.9653; jtursi@astm.org Release #11790 ###
-
ASTM International’s plastic piping systems committee ( F17 ) has approved a new standard that will aid in the manufacture of piping systems to transport fluids and gases. “Entities and companies needing a corrosion-resistant piping system for the transport of aggressive fluids at elevated temperatures will be interested in this new standard,” says ASTM member Tom Walsh, Walsh Consulting Services…
-
New Test Method for Evaluating Resistance of Polypropylene Pressure Piping to Disinfectants ApprovedASTM International’s plastic piping systems committee ( F17 ) has approved a new standard test method that will help ensure polypropylene pressure piping materials are suitably resistant to the presence of disinfectants in potable water systems. “In North America, we use much higher levels of disinfectants such as chlorine in our potable water systems than in most other countries,” says ASTM…
-
Particle size distribution is an important factor in the manufacture of many products, from cement to perfume. A proposed ASTM International standard ( WK45240 ) will set out a general approach to the particle size distribution measurement of powders, suspensions, or slurries using an appropriate wet or dry methodology by the laser diffraction technique. ASTM’s committee on particle and spray…
-
ASTM International’s plastic piping systems committee ( F17 ) has approved a standard that will aid in the design of a new fabricated pipe fittings made from crosslinked polyethylene (CX-PE). The new standard will soon be published as F3525. ASTM International member Robert Samplonius says that F3525 is part of a movement to develop several standards applicable to the specification and…
-
New standard practices and specifications developed by ASTM International’s plastic piping systems committee ( F17 ) establish requirements and test methods for polyamide-12 (PA12) materials, pipe, and fittings. PA12 line pipe is made using polyamide-12, a specialty type of nylon plastic with exceptional strength and durability compared to other plastics used in pressure piping systems. The new…, Media Inquiries:, Jaime Martorana, tel +1.610.832.9796; jmartorana@astm.org, Committee Contact:, Robert Morgan, tel +1.610.832.9732; rmorgan@astm.org Release #11271 ###
-
ASTM International’s plastic piping systems committee ( F17 ) is developing a proposed standard that will cover plastic bodied mechanical fittings for use with outside diameter control polyethylene (PE) water service tube and piping. Municipal water authorities will be the primary users of this proposed standard. According to ASTM International member Alan Brock, the proposed standard will fill…, Media Inquiries:, Jaime Martorana, tel +1.610.832.9796; jmartorana@astm.org, Committee Contact:, Robert Morgan, tel +1.610.832.9732; rmorgan@astm.org Release #11136 ###
-
A new ASTM International standard will help determine procedures for making butt fusion joints with Polyamide 12 (PA12) pipe and fitting by means of heat fusion joining. ASTM’s plastic piping systems committee ( F17 ) developed the standard, which will soon be published as F3372. According to ASTM International member Jim Mason, of Mason Materials Development LLC, “Having an industry consensus…, Media Inquiries:, Dan Bergels, tel +1.610.832.9602; dbergels@astm.org, Committee Contact:, Robert Morgan, tel +1.610.832.9732; rmorgan@astm.org Release #11041 ###
-
A proposed ASTM International standard would be used to evaluate the resistance of polypropylene piping to deterioration when used in circulating domestic hot water systems. ASTM’s plastic piping systems committee ( F17 ) is developing the proposed standard ( WK66288 ). “In most commercial hot water systems, the water is continuously circulated through the main portion of the piping so that…, Media Inquiries:, Dan Bergels, tel +1.610.832.9602; dbergels@astm.org, Committee Contact:, Robert Morgan, tel +1.610.832.9732; rmorgan@astm.org Release #11031 ###
-
A new ASTM International standard will help determine impurities in monoethylene glycol (MEG). ASTM’s committee on aromatic, industrial, specialty, and related chemicals ( D16 ) developed the standard, which will soon be published as D8311. MEG is used predominantly as a raw material in the production of polyester fibers, but it is also commonly used as a heat transfer fluid and a component in…, Media Inquiries:, Dan Bergels, tel +1.610.832.9602; dbergels@astm.org, Committee Contact:, Melissa Marcinowski, tel +1.610.832.9626; mmarcinowski@astm.org Release #11024 ###