Search
Advanced search
Filter by category
Filter by committee
Search results
-
ASTM International’s particle and spray characterization committee ( E29 ) is developing a proposed standard that will be used to measure physical and chemical properties of nanoparticles in a variety of industrial realms. The standard ( E3427 ) describes how to use laser-amplified detection/power spectrum analysis to measure the number of physical and chemical properties of nanoparticles,…, Media Inquiries:, Gavin O’Reilly, tel +1.610.832.9618; goreilly@astm.org, Committee Contact:, Jennifer Tursi, tel +1.610.832.9653; jtursi@astm.org Release #11790 ###
-
ASTM International has announced the launch of a foundational level eLearning certificate program on requirements for medical-related professionals within the cannabis and hemp industries. The program is now available through the MM411 Learning Center. The new program is based on ASTM’s guide for requirements for medical-related professionals within the cannabis and hemp industries ( D8452 ). It…, Media Inquiries:, Gavin O’Reilly, tel +1.610.832.9618; goreilly@astm.org Release #11779 ###
-
ASTM International’s nuclear fuel cycle committee ( C26 ) has developed a standard describing a new technique for measuring the forward rate of glass corrosion. The new standard (soon to be published as C1926) details the stirred-reactor coupon analysis (SRCA) method, in which monolithic glass coupons are partially masked with an inert material before undergoing corrosion in a large volume of…, Media Inquiries:, Gavin O’Reilly, tel +1.610.832.9618; goreilly@astm.org, Committee Contact:, Steve Mawn, tel +1.610.832.9726; smawn@astm.org Release #11649 ###
-
ASTM International’s light sport aircraft committee ( F37 ) has approved a new standard that addresses aeroelasticity requirements of light sport aircraft. Aeroelasticity refers to the interaction of aerodynamic, inertial, and elastic forces that emerge during the relative movement of air and aircraft. According to ASTM member Rian Johnson, the new specification ( F3619 ) defines the standards…, Media Inquiries:, Gavin O’Reilly, tel +1.610.832.9618; goreilly@astm.org, Committee Contact:, Joe Koury, tel +1.610.832.9804; jkoury@astm.org Release #11642 ###
-
A new ASTM International standard addresses size and position of thread inserts for wakeboards. The standard was developed by ASTM’s snow and water sports committee ( F27 ). As ASTM International member Bethany Suderman explains, threaded inserts are used to attach wakeboard bindings to the wakeboard. Each manufacturer specifies where the threaded inserts are positioned on a wakeboard. This…, Media Inquiries:, Dan Bergels, tel +1.610.832.9602; dbergels@astm.org, Committee Contact:, Joe Koury, tel +1.610.832.9804; jkoury@astm.org Release #11521 ###, ,
-
Particle size distribution is an important factor in the manufacture of many products, from cement to perfume. A proposed ASTM International standard ( WK45240 ) will set out a general approach to the particle size distribution measurement of powders, suspensions, or slurries using an appropriate wet or dry methodology by the laser diffraction technique. ASTM’s committee on particle and spray…
-
ASTM International’s autonomy design and operations in aviation administrative committee (AC377) is hosting the 2nd Annual ASTM Autonomy in Aviation Symposium, October 19, 2021, to be held at the Santa Clara Marriott (Santa Clara, California, USA). The objective of the symposium is to facilitate discussions on standards development for aviation autonomy while bringing forward perspectives from…, Media Inquiries:, Jaime Martorana, tel +1.610.832.9796; jmartorana@astm.org Release #11289 ###
-
ASTM International’s snow and water sports committee ( F27 ) is developing a standard that will be used to determine how resistant a water ski is to permanent bending. The proposed standard ( WK69725 ) will also be used to test the basic strength of skis. “This proposed standard will ensure that all manufacturers who comply will test slalom water skis in the same way so that the skis can be…, Media Inquiries:, Jaime Martorana, tel +1.610.832.9796; jmartorana@astm.org , Committee Contact:, Joe Koury, tel +1.610.832.9804; jkoury@astm.org Release #11155 ###
-
Today, global standards developer ASTM International announced the publication of a new technical report on aviation. The report, “Developmental Pillars of Increased Autonomy for Aircraft Systems”, was developed by ASTM’s autonomy design and operations in aviation administrative committee (AC377). The new report is intended to promote the sound application of technical best practices to increase…, Media Inquiries, : Dan Bergels, tel +1.610.832.9602; dbergels@astm.org Release #11054 ###
-
A new ASTM International standardized test method for fiber rope aims to support safety and performance of ropes used to tow inflatable recreational equipment behind boats. The snow and water sports committee approved the new standard (soon to be published as F3410). According to ASTM International member Bethany Suderman, the standard can help various manufacturers test their ropes in the same…, Media Inquiries:, Dan Bergels, tel +1.610.832.9602; dbergels@astm.org, Committee Contact:, Joe Koury, tel +1.610.832.9804; jkoury@astm.org Release #10931