Search
Advanced search
Filter by category
Filter by committee
Search results
-
ASTM International’s particle and spray characterization committee ( E29 ) is developing a proposed standard that will be used to measure physical and chemical properties of nanoparticles in a variety of industrial realms. The standard ( E3427 ) describes how to use laser-amplified detection/power spectrum analysis to measure the number of physical and chemical properties of nanoparticles,…, Media Inquiries:, Gavin O’Reilly, tel +1.610.832.9618; goreilly@astm.org, Committee Contact:, Jennifer Tursi, tel +1.610.832.9653; jtursi@astm.org Release #11790 ###
-
Particle size distribution is an important factor in the manufacture of many products, from cement to perfume. A proposed ASTM International standard ( WK45240 ) will set out a general approach to the particle size distribution measurement of powders, suspensions, or slurries using an appropriate wet or dry methodology by the laser diffraction technique. ASTM’s committee on particle and spray…
-
ASTM International’s concrete pipe committee ( C13 ) has approved a new standard that will help in manufacturing circular concrete pipe that is installed using pipe jacking techniques. The type of pipe covered by the new standard is typically used to convey sewage, industrial wastes, stormwater, or utilities. Engineers, precast concrete pipe manufacturers, and jacking contractors will be the…
-
A proposed ASTM International standard for carbon intensity score will help consumers who want to make purchase decisions based on sustainable bio-based products. ASTM’s industrial biotechnology committee ( E62 ) is developing the proposed standard. ASTM International Board of Directors member Rina Singh notes that a carbon intensity (CI) score placed as a seal on a variety of products would be…, Media Inquiries:, Jaime Martorana, tel +1.610.832.9796; jmartorana@astm.org , Committee Contact:, Pat Picariello, tel +1.610.832.9720; ppicariello@astm.org Release #11212 ###
-
New ASTM International Standard Is First for Testing Corrosion Effects in Manufacturing of AdditivesA new standard developed by ASTM International’s concrete pipe committee ( C13 ) is the first standard test for determining the effectiveness of antimicrobial additives on the corrosion of concrete. “This standard presents test methods to help determine effects of biogenic acidification on concrete products and/or the efficacy of antimicrobial products to resist microbially-induced corrosion in…, Media Inquiries:, Jaime Martorana, tel +1.610.832.9796; jmartorana@astm.org, Committee Contact:, Jimmy Farrell, tel +1.610.832.9661; jfarrell@astm.org Release #11124 ###
-
In light of COVID-19 (coronavirus) and growing safety concerns for members and staff, ASTM International announced today that previously scheduled April standards development meetings in Boston (March 29-April 3) and Prague (April 27-30) have been canceled. The decision was based on several factors, including, but not limited to: Continued review of information and recommendations from the U.S.…, Media Inquiries:, Dan Bergels, tel +1.610.832.9602; dbergels@astm.org Release #10993
-
A new ASTM International standard will serve as a guide for standards related to determining the effects of biogenic sulfuric acid on concrete products. ASTM’s concrete pipe committee approved the standard, which is soon to be published as C1894. According to ASTM International member Mel Marshall, the new standard fills the need for a guide that discusses microbially induced corrosion (MIC) of…, Media Inquiries:, Dan Bergels, tel +1.610.832.9602; dbergels@astm.org, Committee Contact:, Jimmy Farrell, tel +1.610.832.9661; jfarrell@astm.org Release #10898
-
ASTM International’s industrial biotechnology committee ( E62 ) approved a new standard (soon to be published as E3214) that will help classify microorganisms. “The designation of microbe-based products as either genetically modified organisms (GMOs) or not is too simplistic,” said ASTM International member Joseph McAuliffe, senior principal scientist at DuPont Industrial Biosciences. “This…, Media Inquiries:, Dan Bergels, tel +1.610.832.9602; dbergels@astm.org, Committee Contact:, Pat Picariello, tel +1.610.832.9720; ppicariello@astm.org Release #10804
-
A new ASTM International standard will help manufacturers of particulates, such as sand, gravel, and grit, to better measure their products. According to ASTM International member Paul O’Brien, engineering manager at JM Canty, the new guide explains a way to correlate different types of instruments that measure solid-particle distributions. Using the new standard will help expand the capability…, Media Inquiries:, Dan Bergels, tel +1.610.832.9602; dbergels@astm.org, Committee Contact:, Molly Lynyak, tel +1.610.832.9743; mlynyak@astm.org Release #10674
-
ASTM International’s committee on particle and spray characterization ( E29 ) is working on a new standard that aims to reduce uncertainty from an existing test method (bubble point test) for woven wire filter cloth. The material, also known as Dutch weave, is used for general industrial filtration including separation of solids from fluids. The bubble point test determines the pressure at the…, Media Inquiries:, Dan Bergels, tel +1.610.832.9602; dbergels@astm.org, Committee Contact:, Molly Lynyak, tel +610.832.9743; mlynyak@astm.org Release #10657