Search
Advanced search
Filter by category
Filter by committee
Search results
-
There has been a renewed interest in instrumental qualification and standardization by the fluorescence community over the last 10 years, driven by the increasing number of quantitative chemical assays that use fluorescence detection and the presence of regulations in some of these areas. After revising three test methods for fluorescence instruments, stakeholders decided that a standard guide…
-
A proposed new ASTM standard will assist in establishing tests for fretting fatigue, an issue at attachments and joints in a variety of mechanical, aeronautical and biomedical engineering systems and devices. WK24298 , Guide for Fretting Fatigue Testing, is being developed by Subcommittee E08.05 on Cyclic Deformation and Fatigue Crack Formation, part of ASTM International Committee E08 on Fatigue…, ASTM Committee E08 Next Meeting:, May 17-20, 2010, May Committee Week, St. Louis, Mo., Technical Contact:, Richard W. Neu, Georgia Institute of Technology, Atlanta, Ga., Phone: 404-894-3074; rick.neu@gatech.edu, ASTM Staff Contact:, Jeff Adkins, Phone: 610-832-9738; jadkins@astm.org, ASTM PR Contact:, Barbara Schindler, Phone: 610-832-9603; bschindl@astm.org Release #8430/Dec2009
-
The measurement of acid mist is becoming increasingly important due to recent actions taken by the U.S. Environmental Protection Agency on fine particles (2.5 micrometers in diameter and smaller) that are unhealthy to breathe. ASTM International Committee D22 on Air Quality is currently working on a proposed standard for measuring acid mists that come from combustion sources, WK22846 , Test…
-
Data produced from the use of a proposed new ASTM International standard will be employed in the design of new, more efficient aircraft engines as well as for piping, steam and gas turbines used in power generation. The proposed new standard, WK21984 , Test Method for Creep-Fatigue Crack Growth Rate Testing, is being developed by Subcommittee E08.06 on Crack Growth Behavior, part of ASTM…
-
ASTM Committee F10 on Livestock, Meat and Poultry Evaluation Systems has approved a new standard, F2717 , Guide for the Development of Independent Third-Party Verification. The standard, which was developed by Subcommittee F10.20 on Device Performance Criteria, provides an internationally recognized set of guidelines for companies that test the accuracy of livestock, meat and poultry evaluation…
-
A new ASTM International standard provides guidance for using data generated by ASTM standards in testing for asbestos in surface dust. ASTM D 7390 , Guide for Evaluating Asbestos in Dust on Surfaces by Comparison Between Two Environments, was approved by ASTM International Committee D22 on Air Quality, part of Subcommittee D22.07 on Sampling and Analysis of Asbestos. According to James Millette…
-
Committee F10 on Livestock, Meat, and Poultry Evaluation Systems invites all interested parties to join in the standards developing activities of a new task group on radio frequency identification (RFID). The new task group, which is under the jurisdiction of Subcommittee F10.20 on Device Performance Criteria, will have its first meeting Nov. 1 at the November Committee Week in Tampa, Fla. The…
-
A new ASTM International standard will provide a method to consistently address indoor air quality complaints in residential buildings and to guide IAQ investigations in an efficient manner. The standard, D 7297 , Practice for Evaluating Residential Indoor Air Quality Concerns, is under the jurisdiction of Subcommittee D22.05 on Indoor Air, part of ASTM International Committee D22 on Air Quality…
-
Laboratories that measure fibers in workplace samples will be the most likely users of two new ASTM International standards: D 7200 , Practice for Sampling and Counting Airborne Fibers, Including Asbestos Fibers, in Mines and Quarries, by Phase Contrast Microscopy and Transmission Electron Microscope; and D 7201 , Practice for Sampling and Counting Airborne Fibers, Including Asbestos Fibers, in…
-
Verifying the results of application software used to calculate the mechanical properties of materials is the subject of a new standard developed by ASTM International Committee E08 on Fatigue and Fracture. The new standard, E 2443, Guide for Verifying Computer-Generated Test Results Through the Use of Standard Data Sets, is under the jurisdiction of Subcommittee E08.03 on Advanced Apparatus and…