Search
Advanced search
Filter by category
Filter by committee
Search results
-
The measurement of acid mist is becoming increasingly important due to recent actions taken by the U.S. Environmental Protection Agency on fine particles (2.5 micrometers in diameter and smaller) that are unhealthy to breathe. ASTM International Committee D22 on Air Quality is currently working on a proposed standard for measuring acid mists that come from combustion sources, WK22846 , Test…
-
No industry standard currently exists that addresses the vacuum sealing requirements of knife-edged flanges for high vacuum applications. Existing international standards focus on interchangeability of the hardware, but do not address the reliability of the seal. ASTM International Committee E42 on Surface Analysis is now working on a proposed standard on the subject, WK21206 , Specification…
-
A 2002 workshop on galling wear held by ASTM International Committee G02 on Wear and Erosion provided the impetus for the development of a new standard, ASTM G196 , Test Method for Galling Resistance of Material Couples. The new standard is under the jurisdiction of Subcommittee G02.40 on Non-Abrasive Wear. According to Scott Hummel, Ph.D., associate professor, head of the department of…
-
ASTM International Committee F03 on Gaskets has developed and approved a new standard that can be used to evaluate gasket materials covered by ASTM F104 , Classification System for Nonmetallic Gasket Materials. The new standard, F2716 , Practice for Comparison of Nonmetallic Flat Gaskets in High Pressure Saturated Steam, is under the jurisdiction of Subcommittee F03.10 on Composite Gaskets. ASTM…
-
A new ASTM International standard responds to a recent emphasis by regulatory agencies that firms manufacturing drug products demonstrate the efficacy of disinfectants used in controlled environments. The standard, ASTM E2614 , Guide for Evaluation of Cleanroom Disinfectants, was developed by Subcommittee E35.15 on Antimicrobial Agents, part of ASTM International Committee E35 on Pesticides and…
-
A new ASTM International standard provides guidance for using data generated by ASTM standards in testing for asbestos in surface dust. ASTM D 7390 , Guide for Evaluating Asbestos in Dust on Surfaces by Comparison Between Two Environments, was approved by ASTM International Committee D22 on Air Quality, part of Subcommittee D22.07 on Sampling and Analysis of Asbestos. According to James Millette…
-
A new ASTM International standard will provide a method to consistently address indoor air quality complaints in residential buildings and to guide IAQ investigations in an efficient manner. The standard, D 7297 , Practice for Evaluating Residential Indoor Air Quality Concerns, is under the jurisdiction of Subcommittee D22.05 on Indoor Air, part of ASTM International Committee D22 on Air Quality…
-
Laboratories that measure fibers in workplace samples will be the most likely users of two new ASTM International standards: D 7200 , Practice for Sampling and Counting Airborne Fibers, Including Asbestos Fibers, in Mines and Quarries, by Phase Contrast Microscopy and Transmission Electron Microscope; and D 7201 , Practice for Sampling and Counting Airborne Fibers, Including Asbestos Fibers, in…
-
A proposed new standard currently being developed by ASTM International Committee F01 on Electronics will prove to be useful to the tantalum sputtering target industry. The proposed standard, WK9490, Test Method for Reporting Crystallographic Orientation of Sputtering Target Materials, is under the jurisdiction of Subcommittee F01.17 on Sputter Metallization. "The tantalum sputtering target…
-
ASTM International Committee F01 on Electronics is currently developing a proposed new standard that will provide uniformity in the values reported for oxygen content in aluminum alloys used for sputtering targets in the manufacture of integrated circuits. The proposed standard, WK9120, Determination of Oxygen in High Purity Aluminum and Alloys in High Purity Aluminum Base by Inert Gas Fusion…