Search
Advanced search
Filter by category
Filter by committee
Search results
-
A need for a scientifically based procedure to identify equivalent test severity conditions between a 1.707-m diameter laboratory roadwheel surface and a flat or highway surface for radial pneumatic light truck tires has led to the development and approval of a new ASTM International standard. The new standard, ASTM F2869 , Practice for Radial Light Truck Tires to Establish Equivalent Test…
-
A new ASTM International standard will provide how-to information to consultants and contractors for assessing the condition of a roof to be coated and recommendations on how to prepare a roof for a coating. The new standard, ASTM D7120 , Guide for Evaluation and Preparation of Roof Membranes for Coating Application, was developed by Subcommittee D08.20 on Roofing Membrane Systems, part of ASTM…, ASTM Committee D08 Next Meeting:, June 12-15, 2011, June Committee Week, Anaheim, Calif., Technical Contact:, Carter Slusher, Firestone Building Products, Indianapolis, Ind., Phone: 317-575-7117; slushercarter@firesonebp.com, ASTM Staff Contact:, Joseph Hugo, Phone: 610-832-9740; jhugo@astm.org, ASTM PR Contact:, Barbara Schindler, Phone: 610-832-9603; bschindl@astm.org Release #8721
-
In the Transportation Recall Enhancement, Accountability and Documentation Act, the U.S. Congress indicated the need for an aging test on light vehicle tires. Since no industry or government standard addressed this subject, ASTM Committee F09 on Tires developed ASTM F2838 , Practice for Accelerated Laboratory Aging of Radial Passenger Car and Light Truck Tire Through Load Range E for the…
-
The purpose of a laboratory roadwheel test is to realistically evaluate tires for specific road conditions. To facilitate such tests, ASTM International Committee F09 on Tires has developed a practice to provide an industry standard for commercial radial truck-bus tire laboratory temperature algorithms. The algorithms equilibrate with flat surface (highway) operating temperatures to determine…
-
The ongoing focus on sustainability in construction has contributed to greater interest in vegetative, or green, roof systems, in which traditional roofing material is replaced or supplemented with vegetation. A proposed new ASTM International standard will address an important aspect of designing this kind of roofing: determining the proper roofing and waterproofing membrane for a particular…
-
A rim slip performance test for tires that has been done at the Nevada Automotive Test Center for more than 20 years has now become an ASTM International standard. ASTM F2803 , Test Method for Evaluating Rim Slip Performance of Tires and Wheels, was developed by Subcommittee F09.20 on Vehicular Testing, part of ASTM International Committee F09 on Tires. Rim slip occurs when tire and wheel…, ASTM Committee F09 Next Meeting:, April 21-22, April committee week, St. Louis, Mo., Technical Contact:, Jason Whiteley, Nevada Automotive Test Center, Silver Springs, Nev., Phone: 775-629-2000, jwhiteley@natc-ht.com, ASTM Staff Contact:, Rick Lake, Phone: 610-832-9689; rlake@astm.org, ASTM PR Contact:, Barbara Schindler, Phone: 610-832-9603; bschindl@astm.org Release #8494/Feb2010
-
ASTM International Subcommittee E34.50 on Health and Safety Standards for Metalworking Fluids has developed three new standards. Two of the recently approved ASTM standards cover aspects of water-miscible metalworking fluids, while the third concerns prevention of dermatitis in the wet metal removal fluid environment., Prevention of Dermatitis, Dermatitis is an inflammatory response of the skin to a chemical or physical agent. While redness, swelling and itching are typical signs of dermatitis, symptoms can be more severe as well. A new ASTM standard, ASTM E2693 , Practice for Prevention of Dermatitis in the Wet Metal Removal Fluid Environment, discusses dermatitis and its causes and presents a comprehensive approach to dermatitis…, Metalworking Fluids, Two new E34.50 standards address the detection of microbial contamination in metalworking fluids: ASTM E2657 , Test Method for Determination of Endotoxin Concentrations in Water-Miscible Metalworking Fluids, and ASTM E2694 , Test Method for Measurement of Adenosine Triphosphate in Water-Miscible Metalworking Fluids. Both ASTM E2657 and ASTM E2694 measure biological contamination in metalworking…, Participation Invited, The subcommittee is currently looking for participants for an interlaboratory study for ASTM E2657 and ASTM E2694 . “We plan to use a single set of MWF for both standards, so labs who are interested in either or both are welcome to participate,” says Passman. “A few labs will run both the ILS’s for both standards, while most will run one or the other.” Subcommittee E34.50 is part of ASTM…
-
When fasteners penetrate roofing or waterproofing products as a planned part of installation, it is expected in some cases that the product will resist water migration at the point of penetration. A new ASTM International standard, D7349 , Test Method for Determining the Capability of Roofing and Waterproofing Materials to Seal Around Fasteners, addresses this situation. ASTM D7349 was developed…
-
Modified bitumen products have been in use since the mid-1970s, and represent a substantial percentage of the commercial asphalt roofs installed throughout North America. A new ASTM International standard addresses the use of cold process adhesives in modified bitumen roofing systems. ASTM D7379 , Test Methods for Strength of Modified Bitumen Sheet Material Laps Using Cold Process Adhesive, was…
-
All interested parties in the glass industry are invited to participate in the development of a proposed new standard guide for the safe handling of annealed glass. The new standard will be developed by a task group within ASTM Committee E34 on Occupational Health and Safety. A small group from industry and OSHA met in Rossford, Ohio, in March to discuss this new activity. The task group plans to…