Search
Advanced search
Filter by category
Filter by committee
Search results
-
New regulations set forth by the U.S. Environmental Protection Agency to mandate greenhouse gas reporting in the U.S. carbon black industry have led to the development of a new ASTM International standard, ASTM D7662 , Test Method for Carbon Content in Carbon Black Feedstock Oils. ASTM D7662 is under the jurisdiction of Subcommittee D24.66 on Environment, Health and Safety, part of ASTM…
-
A new ASTM International standard will provide how-to information to consultants and contractors for assessing the condition of a roof to be coated and recommendations on how to prepare a roof for a coating. The new standard, ASTM D7120 , Guide for Evaluation and Preparation of Roof Membranes for Coating Application, was developed by Subcommittee D08.20 on Roofing Membrane Systems, part of ASTM…, ASTM Committee D08 Next Meeting:, June 12-15, 2011, June Committee Week, Anaheim, Calif., Technical Contact:, Carter Slusher, Firestone Building Products, Indianapolis, Ind., Phone: 317-575-7117; slushercarter@firesonebp.com, ASTM Staff Contact:, Joseph Hugo, Phone: 610-832-9740; jhugo@astm.org, ASTM PR Contact:, Barbara Schindler, Phone: 610-832-9603; bschindl@astm.org Release #8721
-
The ongoing focus on sustainability in construction has contributed to greater interest in vegetative, or green, roof systems, in which traditional roofing material is replaced or supplemented with vegetation. A proposed new ASTM International standard will address an important aspect of designing this kind of roofing: determining the proper roofing and waterproofing membrane for a particular…
-
The U.S. Environmental Protection Agency has set forth new regulations that mandate greenhouse gas reporting in the U.S. carbon black industry. These regulations were the impetus for the development of a new ASTM International standard, ASTM D7633 , Test Method for Carbon Black Carbon Content. The new standard was developed by Subcommittee D24.66 on Environment, Health and Safety, part of ASTM…, ASTM Committee D24 Next Meeting:, Dec. 6-8, December Committee Week, New Orleans, La., Technical Contact:, George Joyce, Columbian Chemicals Co., Marietta, Ga., Phone: 770-792-9467; gjoyce@columbianchemicals.com, ASTM Staff Contact:, Joe Koury, Phone: 610-832-9804; jkoury@astm.org, ASTM PR Contact:, Barbara Schindler, Phone: 610-832-9603; bschindl@astm.org Release #8641
-
A series of proposed new standards being developed by ASTM International Committee D15 on Engine Coolants would remove technical barriers that currently prevent the cost-effective replacement of ethylene glycol with more environmentally friendly glycerin in antifreeze. The proposed standards are under the jurisdiction of Subcommittee D15.93 on Research and Long Range Planning. Natural glycerin is…
-
An increased interest in the polyaromatic hydrocarbon content of carbon black, particularly in Europe, and new U.S. Environmental Protection Agency requirements to report greenhouse gas emissions from U.S. industry including carbon black plants has led to the formation of a new ASTM subcommittee. Subcommittee D24.66 on Environment, Health and Safety is part of ASTM International Committee D24 on…
-
When fasteners penetrate roofing or waterproofing products as a planned part of installation, it is expected in some cases that the product will resist water migration at the point of penetration. A new ASTM International standard, D7349 , Test Method for Determining the Capability of Roofing and Waterproofing Materials to Seal Around Fasteners, addresses this situation. ASTM D7349 was developed…
-
Modified bitumen products have been in use since the mid-1970s, and represent a substantial percentage of the commercial asphalt roofs installed throughout North America. A new ASTM International standard addresses the use of cold process adhesives in modified bitumen roofing systems. ASTM D7379 , Test Methods for Strength of Modified Bitumen Sheet Material Laps Using Cold Process Adhesive, was…
-
In response to changing emissions restrictions and consumer expectations, ASTM International Committee D15 on Engine Coolants is now developing a proposed new standard, WK16003 , Specification for Engine Coolant Grade 1,3-propanediol (PDO). This task group is under the jurisdiction of Subcommittee D15.07 on Specifications. Edward Eaton, D15 member and chief engineer, Amalgatech, says that as…
-
ASTM International Committee F16 on Fasteners has recently approved an important new standard that deals with coated threaded fasteners and washers by hot-dip zinc galvanizing. The standard, F 2329, Specification for Zinc Coating, Hot-Dip, Requirements for Application to Carbon and Alloy Steel Bolts, Screws, Washers, Nuts and Special Threaded Fasteners, is under the jurisdiction of Subcommittee…