Search
Advanced search
Filter by category
Filter by committee
Search results
-
Although alkali resistant glass fibers have been commercially available for more than 30 years, there has not been an official standard that clearly defines what is required to make glass fibers resistant to alkali attack without the need for protective coatings. ASTM International Committee C27 on Precast Concrete Products has recently developed such a standard, C 1666/C 1666M , Specification…
-
Since 1998, when ASTM International Committee F05 on Business Imaging Products first approved standard F 1856 , Practice for Determining Toner Usage for Printer Cartridges, there has been a rapid increase in the use of color in office printing. In order to address this important change, Subcommittee F05.04 on Electrostatic Imaging Products has developed F 2632 , Practice for Determining the Toner…
-
A new ASTM International standard, F 2490 , Guide for Aircraft Electrical Load and Power Source Capacity Analysis, has been accepted by the Federal Aviation Administration (FAA) as a means of compliance with 14 CFR 23.1351(a) (2), Electrical System Capacity for Part 23 (and Predecessor) Aircraft. Guide F 2490 was developed by Subcommittee F39.01 on Design, Alteration, and Certification, which is…
-
Ineffective removal of grease from restaurants poses a variety of serious environmental problems. Large quantities of grease in public sanitary sewer systems can cause stoppages of piping networks and create costly and time-consuming problems at treatment plants. Sewer backups resulting from grease can also create health hazards when raw sewage backs up into homes or businesses. While grease…
-
The ability to determine the number of pages an ink jet printer cartridge will print in its lifetime is essential for anyone who manufactures or remanufactures them. A new ASTM International standard, F 2555 , Practice for Determining Page Yield of Ink Jet Printer Cartridges — Continuous Printing Method, has been developed to aid in this endeavor. Practice F 2555 is under the jurisdiction of…
-
ASTM International Committee F16 on Fasteners has recently approved an important new standard that deals with coated threaded fasteners and washers by hot-dip zinc galvanizing. The standard, F 2329, Specification for Zinc Coating, Hot-Dip, Requirements for Application to Carbon and Alloy Steel Bolts, Screws, Washers, Nuts and Special Threaded Fasteners, is under the jurisdiction of Subcommittee…
-
ASTM International Committee F05 on Business Imaging Products is currently seeking participation in the development of proposed new standards under the jurisdiction of Subcommittee F05.07 on Ink Jet Imaging Products. Users, original equipment manufacturers and ink producers are needed to assist in the following task groups: F05.07.01 This task group is working on developing a user-friendly…
-
ASTM International Committee F16 on Fasteners has developed a new standard, F 2329, Specification for Zinc Coating, Hot-Dip, Requirements for Application to Carbon and Alloy Steel Bolts, Screws, Washers, Nuts, and Special Threaded Fasteners. The standard, which is under the jurisdiction of Subcommittee F16.03 on Coatings on Fasteners, covers the requirements for hot-dip zinc coating applied to…
-
ASTM International Committee F39 on Normal and Utility Category Airplane Electrical Wiring Systems has approved its first standard, F 2490, Guide for Aircraft Electrical Load and Power Source Capacity Analysis. The new guide covers how to prepare an electrical load analysis to meet Federal Aviation Administration requirements. "This standard is a model for a consistent method of determining the…
-
A proposed new specification currently being developed by ASTM Committee C27 on Precast Concrete Products addresses the issue of watertightness in septic tanks and grease interceptors. The proposed standard, WK7426, Specification for Resilient Connectors Between Reinforced Concrete Tanks and Pipes, is under the jurisdiction of Subcommittee C27.30 on Water and Wastewater Containers. "The entries…