Search
Advanced search
Filter by category
Filter by committee
Search results
-
Quality of materials and proper installation are keys to maintaining the effectiveness, safety and durability of radiant barrier systems used for thermal insulation. Two new ASTM standards will provide important information to both users and installers of radiant barrier systems. The new standards are ASTM C1743 , Practice for Installation and Use of Radiant Barrier Systems (RBS) in Residential…
-
Corrosion inhibitors are used extensively for pipelines in the oil and gas industry. Subcommittee G01.05 on Laboratory Corrosion Tests has been developing a series of standards on performance testing of corrosion inhibitors, including the most recently approved: ASTM G202 , Test Method for Using Atmospheric Pressure Rotating Cage. Subcommittee G01.05 is part of ASTM International Committee G01 on…
-
Localized corrosion, such as pitting, cracking or crevice corrosion, can be destructive to process equipment, but if it is detected early enough, potential damage can be minimized or avoided. A new ASTM International standard provides a means for electrochemical testing for corrosion. The new standard, G199 , Guide for Electrochemical Noise Measurement, was developed by Subcommittee G01.11 on…
-
As a means of ensuring the safety of electrical wiring systems in airplanes, ASTM International Committee F39 on Normal and Utility Category Airplane Electrical Wiring Systems has recently approved F2639 , Practice for Design, Alteration and Certification of Airplane Electrical Wiring Systems, a standard developed by Subcommittee F39.01 on Design, Alteration and Certification. According to…
-
ASTM International Committee C16 on Thermal Insulation will hold a forum on “Thermal Insulation in 2008: Perspectives on Economic Thickness, Contributions to Sustainability, and Design of Power & Process Facilities” on Monday, April 7, 2008, from 5 to 6 p.m., in Anaheim, Calif. The forum will be held in conjunction with the April 6-9 standards development meetings of the committee. Three…
-
Work is continuing on a proposed new ASTM International standard that will aid laboratories and materials manufacturers in testing the moisture properties in construction materials. The proposed standard, WK16466 , Test Method for Moisture Retention Curves of Porous Building Materials Using Pressure Plates, is under the jurisdiction of Subcommittee C16.33 on Insulation Finishes and Moisture, part…
-
A new ASTM International standard, C 1639 , Specification for Fabrication of Cellular Glass Pipe and Tubing Insulation, covers techniques for fabricating cellular glass blocks into billets that are then used to make pipe and tubing insulation. The standard, which was developed by Subcommittee C16.40 on Insulation Systems, part of ASTM International Committee C16 on Thermal Insulation, will be…
-
Andrea Russell, sustainability manager, Rio Tinto Minerals, will speak on "The Basics of Life Cycle Assessment and Insulation" on April 16, 2007, in conjunction with the meetings of ASTM International Committee C16 on Thermal Insulation during the April Committee Week in Norfolk, Va. Russell's presentation, which will take place from 6:00 to 7:00 p.m. at the Waterside Convention Center, is part…
-
ASTM International Subcommittee G01.10 on Corrosion in Soils will be conducting two round robin testing procedures on Tuesday, November 14, from 9:00 a.m. to 3:00 p.m. during ASTM meetings in Atlanta, Ga. One round robin will be for the development of a new standard test method to measure the oxidation-reduction potential (redox) of soils, while the other will address precision and bias for the 4…
-
A new ASTM International standard, F 2490 , Guide for Aircraft Electrical Load and Power Source Capacity Analysis, has been accepted by the Federal Aviation Administration (FAA) as a means of compliance with 14 CFR 23.1351(a) (2), Electrical System Capacity for Part 23 (and Predecessor) Aircraft. Guide F 2490 was developed by Subcommittee F39.01 on Design, Alteration, and Certification, which is…