Search
Advanced search
Filter by category
Filter by committee
Search results
-
Laboratories that have the ability to analyze titanium and titanium alloys by spark-atomic emission spectrometry or glow discharge-AES are currently being sought to participate in an interlaboratory study for a proposed new standard. ASTM WK25738 , Test Method for Analysis of Titanium and Titanium Alloys by Spark-Atomic Emission/Glow Discharge-Atomic Emission Spectrometry, is currently being…, ASTM Committee E01 Next Meeting:, May 15-18, 2011, May Committee Week, Anaheim, Calif., Technical Contact:, Kevin VonScio, Perryman Co., Houston, Pa., Phone: 724-746-9390; kvonscio@perrymanco.com, ASTM Staff Contact:, Thomas O’Toole, Phone: 610-832-9739; totoole@astm.org, ASTM PR Contact:, Barbara Schindler, Phone: 610-832-9603; bschindl@astm.org Release #8855
-
ASTM International Committee D15 on Engine Coolants has formed three new subcommittees: Subcommittees D15.22 on Non-Aqueous Coolants ; D15.25 on Diesel Exhaust Fluid ; and D15.30 on Industrial Heat Transfer Fluids . All interested parties are invited to join in the standards developing activities of these new subcommittees., D15.22, Non-Aqueous Coolants, While there has been an increased interest in non-aqueous coolants industry, there are no current ASTM standards in this area. D15.22 will begin to develop such standards. “The envisioned standards for non-aqueous coolants would be performance standards, rather than ingredient standards, to allow for formulations that are not currently proprietary,” says Jonathan T. Light, chief engineer, Evans…, D15.25, Diesel Exhaust Fluid, Diesel exhaust fluid, often referred to as DEF, is required by many diesel engine-powered vehicles delivered after January 2010. More recent environmental standards issued by the U.S. Environmental Protection Agency have created more stringent emissions standards for agricultural, construction and forestry equipment. DEF is used to reduce nitrogen oxide emissions, which allows original equipment…, D15.30, Industrial Heat Transfer Fluids, Members of D15 recognized that changes in the antifreeze industry, including new manufacturing technologies, improved inhibitor chemistries and recycling technologies, would likely be adapted to the facilities industry as a natural course of innovation. Because D15 has experience developing standards that are technically similar to the facilities heat transfer industry, it was deemed appropriate…, ASTM Committee D15 Next Meeting:, May 17-18, May Committee Week, Anaheim, Calif., Technical Contact:, (D15.22) Jonathan T. Light, Evans Cooling Systems Inc., Sharon, Conn., Phone: 860-435-2418; jtlight@comcast.net ; (D15.25) Edward Eaton Sr., Amalgatech, Phoenix, Ariz., Phone: 602-252-0280; edeaton@amalgatech.com ; (D15.30) John Panasewicz, Clear Choice Antifreeze, Henderson, Colo., Phone: 303-227-9900; johnp@clearchoiceantifreeze.com, ASTM Staff Contact:, Joe Koury, Phone: 610-832-9804; jkoury@astm.org, ASTM PR Contact:, Barbara Schindler, Phone: 610-832-9603; bschindl@astm.org Release #8837
-
Trona, or sodium sesquicarbonate, is a fine mineral powder that has proven to be effective at removing acid gases from air emissions. While trona can be a useful component of air pollution control systems, it can be difficult to handle, particularly when moisture is present. A proposed new ASTM standard will present a repeatable, precise and accurate test method for analyzing moisture levels in…, ASTM Committee E01 Next Meeting:, Nov. 14-17, November Committee Week, San Antonio, Texas, Technical Contact: J, ames D. Phillip, Solvay Chemicals Inc, Green River, Wyo., Phone: 307-872-6519; jim.phillip@solvay.com, ASTM Staff Contact:, Thomas O'Toole, Phone: 610-832-9739; totoole@astm.org, ASTM PR Contact:, Barbara Schindler, Phone: 610-832-9603; bschindl@astm.org Release #8608
-
A series of proposed new standards being developed by ASTM International Committee D15 on Engine Coolants would remove technical barriers that currently prevent the cost-effective replacement of ethylene glycol with more environmentally friendly glycerin in antifreeze. The proposed standards are under the jurisdiction of Subcommittee D15.93 on Research and Long Range Planning. Natural glycerin is…
-
ASTM International Subcommittee E34.50 on Health and Safety Standards for Metalworking Fluids has developed three new standards. Two of the recently approved ASTM standards cover aspects of water-miscible metalworking fluids, while the third concerns prevention of dermatitis in the wet metal removal fluid environment., Prevention of Dermatitis, Dermatitis is an inflammatory response of the skin to a chemical or physical agent. While redness, swelling and itching are typical signs of dermatitis, symptoms can be more severe as well. A new ASTM standard, ASTM E2693 , Practice for Prevention of Dermatitis in the Wet Metal Removal Fluid Environment, discusses dermatitis and its causes and presents a comprehensive approach to dermatitis…, Metalworking Fluids, Two new E34.50 standards address the detection of microbial contamination in metalworking fluids: ASTM E2657 , Test Method for Determination of Endotoxin Concentrations in Water-Miscible Metalworking Fluids, and ASTM E2694 , Test Method for Measurement of Adenosine Triphosphate in Water-Miscible Metalworking Fluids. Both ASTM E2657 and ASTM E2694 measure biological contamination in metalworking…, Participation Invited, The subcommittee is currently looking for participants for an interlaboratory study for ASTM E2657 and ASTM E2694 . “We plan to use a single set of MWF for both standards, so labs who are interested in either or both are welcome to participate,” says Passman. “A few labs will run both the ILS’s for both standards, while most will run one or the other.” Subcommittee E34.50 is part of ASTM…
-
Test Method Covers Inductively Coupled Plasma Atomic Emission Spectrometry, A new ASTM International standard will help users properly prepare and analyze various nickel-based alloy samples by inductively coupled plasma emission spectrometry. The standard, ASTM E2594 , Test Method for Analysis of Nickel Alloys by Inductively Coupled Plasma Atomic Emission Spectrometry (Performance-Based Method), will assist users in preparing sample and calibration solutions and with…
-
Advancing gas analysis technology is leading to the development of a proposed new ASTM International standard, WK22331 , Test Method for Simultaneous Determination of Oxygen, Nitrogen and Hydrogen in Titanium and Titanium Alloys by the Inert Gas Fusion Technique. Analyzers are now available that can simultaneously test titanium and titanium alloys for oxygen, nitrogen and hydrogen. This…
-
All interested parties are invited to join in the ongoing development of a proposed new standard, WK19982 , Test Method for ICP Analysis of Calcium and Magnesium in Magnesium Ferrosilicon. WK19982 is being developed by Subcommittee E01.01 on Iron, Steel and Ferroalloys, part of ASTM International Committee E01 on Analytical Chemistry for Metals, Ores and Related Materials. According to Robert…
-
All interested parties in the glass industry are invited to participate in the development of a proposed new standard guide for the safe handling of annealed glass. The new standard will be developed by a task group within ASTM Committee E34 on Occupational Health and Safety. A small group from industry and OSHA met in Rossford, Ohio, in March to discuss this new activity. The task group plans to…
-
Responding to requests from representatives of the copper industry, ASTM International Committee E01 on Analytical Chemistry for Metals, Ores and Related Materials has developed a new standard, E2575 , Test Method for Determination of Oxygen in Copper and Copper Alloys. The new standard is under the jurisdiction of Subcommittee E01.05 on Cu, Pb, Zn, Cd, Sn, Be, Their Alloys and Related Metals. …