Search
Advanced search
Filter by category
Filter by committee
Search results
-
The ongoing focus on sustainability in construction has contributed to greater interest in vegetative, or green, roof systems, in which traditional roofing material is replaced or supplemented with vegetation. A proposed new ASTM International standard will address an important aspect of designing this kind of roofing: determining the proper roofing and waterproofing membrane for a particular…
-
Trona, or sodium sesquicarbonate, is a fine mineral powder that has proven to be effective at removing acid gases from air emissions. While trona can be a useful component of air pollution control systems, it can be difficult to handle, particularly when moisture is present. A proposed new ASTM standard will present a repeatable, precise and accurate test method for analyzing moisture levels in…, ASTM Committee E01 Next Meeting:, Nov. 14-17, November Committee Week, San Antonio, Texas, Technical Contact: J, ames D. Phillip, Solvay Chemicals Inc, Green River, Wyo., Phone: 307-872-6519; jim.phillip@solvay.com, ASTM Staff Contact:, Thomas O'Toole, Phone: 610-832-9739; totoole@astm.org, ASTM PR Contact:, Barbara Schindler, Phone: 610-832-9603; bschindl@astm.org Release #8608
-
Rapid hardening hydraulic cements are used in a variety of applications in which reduced cementitious contents are desired or early service is needed. Included among these applications are paving, construction, stucco, mortar and block. A newly approved ASTM International standard covering these cements, ASTM C1600/C1600M , Specification for Rapid Hardening Hydraulic Cement, has been developed by…, Type URH, —ultra rapid hardening, for use where ultra high early strength is desired;, Type VRH, —very rapid hardening, for use where very high early strength is desired;, Type MRH, —medium rapid hardening, for use where mid-range rapid hardening, high early strength is desired; and, Type GRH, —general rapid hardening, for use when the higher strength properties of Type VRH or a Type MRH cement is not required. “ASTM C1600 lists minimum requirements for compressive strength, setting time, shrinkage and soundness (autoclave expansion),” says Hicks. “Optional specifications for sulfate expansion, alkali silicate reactions with aggregates, heat of hydration and expansion in water are also…
-
Test Method Covers Inductively Coupled Plasma Atomic Emission Spectrometry, A new ASTM International standard will help users properly prepare and analyze various nickel-based alloy samples by inductively coupled plasma emission spectrometry. The standard, ASTM E2594 , Test Method for Analysis of Nickel Alloys by Inductively Coupled Plasma Atomic Emission Spectrometry (Performance-Based Method), will assist users in preparing sample and calibration solutions and with…
-
Advancing gas analysis technology is leading to the development of a proposed new ASTM International standard, WK22331 , Test Method for Simultaneous Determination of Oxygen, Nitrogen and Hydrogen in Titanium and Titanium Alloys by the Inert Gas Fusion Technique. Analyzers are now available that can simultaneously test titanium and titanium alloys for oxygen, nitrogen and hydrogen. This…
-
When fasteners penetrate roofing or waterproofing products as a planned part of installation, it is expected in some cases that the product will resist water migration at the point of penetration. A new ASTM International standard, D7349 , Test Method for Determining the Capability of Roofing and Waterproofing Materials to Seal Around Fasteners, addresses this situation. ASTM D7349 was developed…
-
Modified bitumen products have been in use since the mid-1970s, and represent a substantial percentage of the commercial asphalt roofs installed throughout North America. A new ASTM International standard addresses the use of cold process adhesives in modified bitumen roofing systems. ASTM D7379 , Test Methods for Strength of Modified Bitumen Sheet Material Laps Using Cold Process Adhesive, was…
-
All interested parties are invited to join in the ongoing development of a proposed new standard, WK19982 , Test Method for ICP Analysis of Calcium and Magnesium in Magnesium Ferrosilicon. WK19982 is being developed by Subcommittee E01.01 on Iron, Steel and Ferroalloys, part of ASTM International Committee E01 on Analytical Chemistry for Metals, Ores and Related Materials. According to Robert…
-
Responding to requests from representatives of the copper industry, ASTM International Committee E01 on Analytical Chemistry for Metals, Ores and Related Materials has developed a new standard, E2575 , Test Method for Determination of Oxygen in Copper and Copper Alloys. The new standard is under the jurisdiction of Subcommittee E01.05 on Cu, Pb, Zn, Cd, Sn, Be, Their Alloys and Related Metals. …
-
A recently approved revision to ASTM International standard C 150 , Specification for Portland Cement, includes three significant technical changes to the document. The changes are part of a joint effort between ASTM and the American Association of State and Highway and Transportation Officials to harmonize C 150 with AASHTO’s standard, M 85, Specification for Portland Cement. C 150 is under the…