Search
Advanced search
Filter by category
Filter by committee
Search results
-
ASTM International Committee F12 on Security Systems and Equipment invites all interested parties to participate in the current revision of ASTM F967 , Practice for Security Engineering Symbols. The standard is under the jurisdiction of Subcommittee F12.10 on Systems, Products and Services. According to Ed Conrath, senior principal, Protection Engineering Consultants, and F12 committee chairman,…
-
A new ASTM International standard will provide how-to information to consultants and contractors for assessing the condition of a roof to be coated and recommendations on how to prepare a roof for a coating. The new standard, ASTM D7120 , Guide for Evaluation and Preparation of Roof Membranes for Coating Application, was developed by Subcommittee D08.20 on Roofing Membrane Systems, part of ASTM…, ASTM Committee D08 Next Meeting:, June 12-15, 2011, June Committee Week, Anaheim, Calif., Technical Contact:, Carter Slusher, Firestone Building Products, Indianapolis, Ind., Phone: 317-575-7117; slushercarter@firesonebp.com, ASTM Staff Contact:, Joseph Hugo, Phone: 610-832-9740; jhugo@astm.org, ASTM PR Contact:, Barbara Schindler, Phone: 610-832-9603; bschindl@astm.org Release #8721
-
The ongoing focus on sustainability in construction has contributed to greater interest in vegetative, or green, roof systems, in which traditional roofing material is replaced or supplemented with vegetation. A proposed new ASTM International standard will address an important aspect of designing this kind of roofing: determining the proper roofing and waterproofing membrane for a particular…
-
“Bumping” is a process that can allow virtually anyone to covertly operate a pin tumbler lock. A long-held locksmith secret, bumping has become more well known as videos describing the process of making and using a bump key have surfaced on the Internet. Potential intruders can use the bumping process to break into homes and other buildings while leaving the impression that something must have…
-
Rapid hardening hydraulic cements are used in a variety of applications in which reduced cementitious contents are desired or early service is needed. Included among these applications are paving, construction, stucco, mortar and block. A newly approved ASTM International standard covering these cements, ASTM C1600/C1600M , Specification for Rapid Hardening Hydraulic Cement, has been developed by…, Type URH, —ultra rapid hardening, for use where ultra high early strength is desired;, Type VRH, —very rapid hardening, for use where very high early strength is desired;, Type MRH, —medium rapid hardening, for use where mid-range rapid hardening, high early strength is desired; and, Type GRH, —general rapid hardening, for use when the higher strength properties of Type VRH or a Type MRH cement is not required. “ASTM C1600 lists minimum requirements for compressive strength, setting time, shrinkage and soundness (autoclave expansion),” says Hicks. “Optional specifications for sulfate expansion, alkali silicate reactions with aggregates, heat of hydration and expansion in water are also…
-
When fasteners penetrate roofing or waterproofing products as a planned part of installation, it is expected in some cases that the product will resist water migration at the point of penetration. A new ASTM International standard, D7349 , Test Method for Determining the Capability of Roofing and Waterproofing Materials to Seal Around Fasteners, addresses this situation. ASTM D7349 was developed…
-
Modified bitumen products have been in use since the mid-1970s, and represent a substantial percentage of the commercial asphalt roofs installed throughout North America. A new ASTM International standard addresses the use of cold process adhesives in modified bitumen roofing systems. ASTM D7379 , Test Methods for Strength of Modified Bitumen Sheet Material Laps Using Cold Process Adhesive, was…
-
A recently approved revision to ASTM International standard C 150 , Specification for Portland Cement, includes three significant technical changes to the document. The changes are part of a joint effort between ASTM and the American Association of State and Highway and Transportation Officials to harmonize C 150 with AASHTO’s standard, M 85, Specification for Portland Cement. C 150 is under the…
-
ASTM International Committee F12 on Security Systems and Equipment has approved a new standard, F 2656 , Test Method for Vehicle Crash Testing of Perimeter Barriers. The new test method, developed by Subcommittee F12.10 on Systems, Products and Services, provides a range of vehicle impact conditions, designations and penetration performance levels for the testing of perimeter barriers that are…
-
It has become a common scene: a driver in a parking lot suddenly loses control of a car, sending it into a storefront or other pedestrian area. In an effort to minimize the injury and damage caused by such crashes, ASTM International Committee F12 on Security Systems and Equipment is developing a proposed new standard, WK13074 , Test Method for Crash Testing of Low Speed Pedestrian Barriers. The…