Search
Advanced search
Filter by category
Filter by committee
Search results
-
Corrosion inhibitors are used extensively for pipelines in the oil and gas industry. Subcommittee G01.05 on Laboratory Corrosion Tests has been developing a series of standards on performance testing of corrosion inhibitors, including the most recently approved: ASTM G202 , Test Method for Using Atmospheric Pressure Rotating Cage. Subcommittee G01.05 is part of ASTM International Committee G01 on…
-
A new ASTM standard will be useful to slide and engine companies, as well as makers of bushing materials, in studies that involve the measurement of system friction forces. The new standard, ASTM G203 , Guide for Determining Friction Energy Dissipation in Reciprocating Tribosystems, was developed by Subcommittee G02.50 on Friction, part of ASTM International Committee G02 on Wear and Erosion.…
-
Rapid hardening hydraulic cements are used in a variety of applications in which reduced cementitious contents are desired or early service is needed. Included among these applications are paving, construction, stucco, mortar and block. A newly approved ASTM International standard covering these cements, ASTM C1600/C1600M , Specification for Rapid Hardening Hydraulic Cement, has been developed by…, Type URH, —ultra rapid hardening, for use where ultra high early strength is desired;, Type VRH, —very rapid hardening, for use where very high early strength is desired;, Type MRH, —medium rapid hardening, for use where mid-range rapid hardening, high early strength is desired; and, Type GRH, —general rapid hardening, for use when the higher strength properties of Type VRH or a Type MRH cement is not required. “ASTM C1600 lists minimum requirements for compressive strength, setting time, shrinkage and soundness (autoclave expansion),” says Hicks. “Optional specifications for sulfate expansion, alkali silicate reactions with aggregates, heat of hydration and expansion in water are also…
-
Localized corrosion, such as pitting, cracking or crevice corrosion, can be destructive to process equipment, but if it is detected early enough, potential damage can be minimized or avoided. A new ASTM International standard provides a means for electrochemical testing for corrosion. The new standard, G199 , Guide for Electrochemical Noise Measurement, was developed by Subcommittee G01.11 on…
-
A recently approved revision to ASTM International standard C 150 , Specification for Portland Cement, includes three significant technical changes to the document. The changes are part of a joint effort between ASTM and the American Association of State and Highway and Transportation Officials to harmonize C 150 with AASHTO’s standard, M 85, Specification for Portland Cement. C 150 is under the…
-
Subcommittee G02.10 on Erosion by Solids and Liquids, part of ASTM International Committee G02 on Wear and Erosion, is interested in hearing from anyone who uses cavitation erosion testing in their work. The objective of this survey is to help the subcommittee determine the current degree of interest in and importance of cavitation erosion test methods. The subcommittee is especially interested…
-
ASTM International Committee B08 on Metallic and Inorganic Coatings has recently approved a revision of one of its most important standards, B 633 , Specification for Electrodeposited Coatings of Zinc on Iron and Steel. B 633 is under the jurisdiction of Task Group B08.08.04 on Soft Metals, which is part of Subcommittee B08.08 on Metallic Coatings. Zinc coatings are used to provide a sacrificial…
-
ASTM International Subcommittee G01.10 on Corrosion in Soils will be conducting two round robin testing procedures on Tuesday, November 14, from 9:00 a.m. to 3:00 p.m. during ASTM meetings in Atlanta, Ga. One round robin will be for the development of a new standard test method to measure the oxidation-reduction potential (redox) of soils, while the other will address precision and bias for the 4…
-
A task group of ASTM International Committee G02 on Wear and Erosion is seeking interested parties to participate in the revision of ASTM G 32, Test Method on Cavitation Erosion Using Vibratory Apparatus. The standard and the task group are under the jurisdiction of Subcommittee G02.10 on Erosion by Solids and Liquids. The task group is specifically seeking participants with any of the following…
-
ASTM International Committee G01 on Corrosion of Metals has an ongoing commitment to help the oilfield and refinery industries adopt and use state-of-the-art techniques to select corrosion inhibitors. As part of this commitment, two new standards developed by Subcommittee G01.05 on Laboratory Corrosion Tests have recently been published: G 184, Practice for Evaluating and Qualifying Oilfield and…