Search
Advanced search
Filter by category
Filter by committee
Search results
-
Determining the pressure rating for PVC plastic pipe is a relatively straightforward process because pipe is a cylinder with a uniform wall thickness. However, establishing a pressure rating for PVC fittings is a more complex process, chiefly because there are many sizes, patterns and variations among manufacturers involved. A new ASTM International standard, F 2261 , Test Method for Pressure…
-
A new ASTM International standard, F 2490 , Guide for Aircraft Electrical Load and Power Source Capacity Analysis, has been accepted by the Federal Aviation Administration (FAA) as a means of compliance with 14 CFR 23.1351(a) (2), Electrical System Capacity for Part 23 (and Predecessor) Aircraft. Guide F 2490 was developed by Subcommittee F39.01 on Design, Alteration, and Certification, which is…
-
ASTM International Committee F40 on Declarable Substances in Materials has recently approved their first standard, F 2576 , Terminology Relating to Declarable Substances in Materials. The standard, which will serve as the committee’s lexicon of terms, abbreviations and units, is under the jurisdiction of Subcommittee F40.91 on Terminology. Nine terms are listed in the standard, which will be…
-
Keeping pipes properly connected is clearly an important aspect of any sewer maintenance system. A new ASTM International standard, F 2561 , Practice for Rehabilitation of a Sewer Service Lateral and Its Connection to the Main Using a One-Piece Main and Lateral Cured-in-Place Liner, has been developed that makes the process of keeping sewer pipelines connected more effective. Practice F 2561 is…
-
ASTM International Committee F16 on Fasteners has recently approved an important new standard that deals with coated threaded fasteners and washers by hot-dip zinc galvanizing. The standard, F 2329, Specification for Zinc Coating, Hot-Dip, Requirements for Application to Carbon and Alloy Steel Bolts, Screws, Washers, Nuts and Special Threaded Fasteners, is under the jurisdiction of Subcommittee…
-
Technical issues with test methods and reference materials identified by ASTM Committee F40 on Declarable Substances in Materials will be among the topics discussed at a workshop hosted by the National Institute of Standards and Technology (NIST) in October. The goal of the workshop is to assist U.S. manufacturers and their supply chains in meeting new environmental regulations that restrict the…
-
ASTM International Committee F16 on Fasteners has developed a new standard, F 2329, Specification for Zinc Coating, Hot-Dip, Requirements for Application to Carbon and Alloy Steel Bolts, Screws, Washers, Nuts, and Special Threaded Fasteners. The standard, which is under the jurisdiction of Subcommittee F16.03 on Coatings on Fasteners, covers the requirements for hot-dip zinc coating applied to…
-
ASTM International Committee F39 on Normal and Utility Category Airplane Electrical Wiring Systems has approved its first standard, F 2490, Guide for Aircraft Electrical Load and Power Source Capacity Analysis. The new guide covers how to prepare an electrical load analysis to meet Federal Aviation Administration requirements. "This standard is a model for a consistent method of determining the…
-
A growing interest in a more durable structure for grease traps has resulted in the development of a proposed new ASTM standard, WK7686, Specification for High Density Polyethylene Grease Trap Interceptor Units. The proposed standard is under the jurisdiction of ASTM Subcommittee F17.26 on Olefin Based Pipe, which is part of Committee F17 on Plastic Piping Systems. "The impetus for developing…
-
ASTM International, one of the largest voluntary standards development organizations in the world, today announced the formation of a new committee to develop standards for the evaluation of materials and products relative to the restriction of certain hazardous substances. Committee F40 on Declarable Substances in Materials will address issues that could have a devastating economic impact on…, Beginning the Standardization Process, On Oct. 15, 2004, representatives from the appliance, electric tool, electronic, laboratory, instrument manufacturing, and supplier sectors affected by RoHS legislation attended a planning meeting at ASTM International Headquarters. They agreed to hold an organizational meeting to discuss the creation of a new standardization activity on declarable substances. The organizational meeting occurred…, Participation Is Open, The development of standards within Committee F40 represents a chance to help the environment while constraining unnecessary compliance costs that may damage many sectors of the world economy. If you are part of the business sectors mentioned above, participation in F40 is in your economic interest. The next meeting of Committee F40 will take place May 26-27, 2005, at ASTM International…