Search
Advanced search
Filter by category
Filter by committee
Search results
-
“Bumping” is a process that can allow virtually anyone to covertly operate a pin tumbler lock. A long-held locksmith secret, bumping has become more well known as videos describing the process of making and using a bump key have surfaced on the Internet. Potential intruders can use the bumping process to break into homes and other buildings while leaving the impression that something must have…
-
Corrosion inhibitors are used extensively for pipelines in the oil and gas industry. Subcommittee G01.05 on Laboratory Corrosion Tests has been developing a series of standards on performance testing of corrosion inhibitors, including the most recently approved: ASTM G202 , Test Method for Using Atmospheric Pressure Rotating Cage. Subcommittee G01.05 is part of ASTM International Committee G01 on…
-
Localized corrosion, such as pitting, cracking or crevice corrosion, can be destructive to process equipment, but if it is detected early enough, potential damage can be minimized or avoided. A new ASTM International standard provides a means for electrochemical testing for corrosion. The new standard, G199 , Guide for Electrochemical Noise Measurement, was developed by Subcommittee G01.11 on…
-
As a means of ensuring the safety of electrical wiring systems in airplanes, ASTM International Committee F39 on Normal and Utility Category Airplane Electrical Wiring Systems has recently approved F2639 , Practice for Design, Alteration and Certification of Airplane Electrical Wiring Systems, a standard developed by Subcommittee F39.01 on Design, Alteration and Certification. According to…
-
ASTM International Committee F12 on Security Systems and Equipment has approved a new standard, F 2656 , Test Method for Vehicle Crash Testing of Perimeter Barriers. The new test method, developed by Subcommittee F12.10 on Systems, Products and Services, provides a range of vehicle impact conditions, designations and penetration performance levels for the testing of perimeter barriers that are…
-
It has become a common scene: a driver in a parking lot suddenly loses control of a car, sending it into a storefront or other pedestrian area. In an effort to minimize the injury and damage caused by such crashes, ASTM International Committee F12 on Security Systems and Equipment is developing a proposed new standard, WK13074 , Test Method for Crash Testing of Low Speed Pedestrian Barriers. The…
-
ASTM International Subcommittee G01.10 on Corrosion in Soils will be conducting two round robin testing procedures on Tuesday, November 14, from 9:00 a.m. to 3:00 p.m. during ASTM meetings in Atlanta, Ga. One round robin will be for the development of a new standard test method to measure the oxidation-reduction potential (redox) of soils, while the other will address precision and bias for the 4…
-
ASTM International Committee F12 on Security Systems and Equipment invites all interested users, specifiers and industry personnel to participate in the development of a proposed new standard, WK11191 , Test Method for Boat Barriers. WK11191 is under the jurisdiction of Subcommittee F12.10 on Systems, Products and Services. The purpose of the WK11191 is to create requirements for any land-based…
-
A new ASTM International standard, F 2490 , Guide for Aircraft Electrical Load and Power Source Capacity Analysis, has been accepted by the Federal Aviation Administration (FAA) as a means of compliance with 14 CFR 23.1351(a) (2), Electrical System Capacity for Part 23 (and Predecessor) Aircraft. Guide F 2490 was developed by Subcommittee F39.01 on Design, Alteration, and Certification, which is…
-
ASTM International Committee G01 on Corrosion of Metals has an ongoing commitment to help the oilfield and refinery industries adopt and use state-of-the-art techniques to select corrosion inhibitors. As part of this commitment, two new standards developed by Subcommittee G01.05 on Laboratory Corrosion Tests have recently been published: G 184, Practice for Evaluating and Qualifying Oilfield and…