Search
Advanced search
Filter by category
Filter by committee
Search results
-
ASTM International’s particle and spray characterization committee ( E29 ) is developing a proposed standard that will be used to measure physical and chemical properties of nanoparticles in a variety of industrial realms. The standard ( E3427 ) describes how to use laser-amplified detection/power spectrum analysis to measure the number of physical and chemical properties of nanoparticles,…, Media Inquiries:, Gavin O’Reilly, tel +1.610.832.9618; goreilly@astm.org, Committee Contact:, Jennifer Tursi, tel +1.610.832.9653; jtursi@astm.org Release #11790 ###
-
A new ASTM International standard addresses size and position of thread inserts for wakeboards. The standard was developed by ASTM’s snow and water sports committee ( F27 ). As ASTM International member Bethany Suderman explains, threaded inserts are used to attach wakeboard bindings to the wakeboard. Each manufacturer specifies where the threaded inserts are positioned on a wakeboard. This…, Media Inquiries:, Dan Bergels, tel +1.610.832.9602; dbergels@astm.org, Committee Contact:, Joe Koury, tel +1.610.832.9804; jkoury@astm.org Release #11521 ###, ,
-
Particle size distribution is an important factor in the manufacture of many products, from cement to perfume. A proposed ASTM International standard ( WK45240 ) will set out a general approach to the particle size distribution measurement of powders, suspensions, or slurries using an appropriate wet or dry methodology by the laser diffraction technique. ASTM’s committee on particle and spray…
-
ASTM International’s snow and water sports committee ( F27 ) is developing a standard that will be used to determine how resistant a water ski is to permanent bending. The proposed standard ( WK69725 ) will also be used to test the basic strength of skis. “This proposed standard will ensure that all manufacturers who comply will test slalom water skis in the same way so that the skis can be…, Media Inquiries:, Jaime Martorana, tel +1.610.832.9796; jmartorana@astm.org , Committee Contact:, Joe Koury, tel +1.610.832.9804; jkoury@astm.org Release #11155 ###
-
A new ASTM International practice provides necessary steps when writing new or revising existing standards that use saturated calomel electrode (SCE) for determining electrode potentials. ASTM’s corrosion of metals committee ( G01 ) developed the standard, soon to be published as G220. “This standard provides useful information for those writing new or revising existing standards where electrode…, Media Inquiries:, Jaime Martorana, tel +1.610.832.9796; jmartorana@astm.org, Committee Contact:, Krista Robbins, tel +1.610.832.9689; krobbins@astm.org Release #11138 ###
-
A new ASTM International standardized test method for fiber rope aims to support safety and performance of ropes used to tow inflatable recreational equipment behind boats. The snow and water sports committee approved the new standard (soon to be published as F3410). According to ASTM International member Bethany Suderman, the standard can help various manufacturers test their ropes in the same…, Media Inquiries:, Dan Bergels, tel +1.610.832.9602; dbergels@astm.org, Committee Contact:, Joe Koury, tel +1.610.832.9804; jkoury@astm.org Release #10931
-
ASTM International has published a new standard that aims to improve the reliability and sustainability of iron water pipes that provide clean drinking water. The organization’s corrosion of metals committee ( G01 ) developed the new standard ( G218 ). According to ASTM International member Mike Horton, there are many standards (related to coatings and cathodic protection) that help protect…, Media Inquiries:, Dan Bergels, tel +1.610.832.9602; dbergels@astm.org, Committee Contact:, Krista Robbins, tel +1.610.832.9689; krobbins@astm.org Release #10903
-
ASTM International’s snow and water sports committee ( F27 ) has launched a new group that will develop standards for water sports equipment. A task group is developing two proposed standards, including one for wakeboard bindings ( WK67020 ). The proposed wakeboard binding standard specifies the size and position of threaded inserts. Threaded inserts are used to attach wakeboard bindings to…, Media Inquiries:, Dan Bergels, tel +1.610.832.9602; dbergels@astm.org, Committee Contact:, Joe Koury, tel +1.610.832.9804; jkoury@astm.org Release #10759
-
A new ASTM International standard will help manufacturers of particulates, such as sand, gravel, and grit, to better measure their products. According to ASTM International member Paul O’Brien, engineering manager at JM Canty, the new guide explains a way to correlate different types of instruments that measure solid-particle distributions. Using the new standard will help expand the capability…, Media Inquiries:, Dan Bergels, tel +1.610.832.9602; dbergels@astm.org, Committee Contact:, Molly Lynyak, tel +1.610.832.9743; mlynyak@astm.org Release #10674
-
ASTM International’s committee on particle and spray characterization ( E29 ) is working on a new standard that aims to reduce uncertainty from an existing test method (bubble point test) for woven wire filter cloth. The material, also known as Dutch weave, is used for general industrial filtration including separation of solids from fluids. The bubble point test determines the pressure at the…, Media Inquiries:, Dan Bergels, tel +1.610.832.9602; dbergels@astm.org, Committee Contact:, Molly Lynyak, tel +610.832.9743; mlynyak@astm.org Release #10657