Search
Advanced search
Filter by category
Filter by committee
Search results
-
ASTM International’s particle and spray characterization committee ( E29 ) is developing a proposed standard that will be used to measure physical and chemical properties of nanoparticles in a variety of industrial realms. The standard ( E3427 ) describes how to use laser-amplified detection/power spectrum analysis to measure the number of physical and chemical properties of nanoparticles,…, Media Inquiries:, Gavin O’Reilly, tel +1.610.832.9618; goreilly@astm.org, Committee Contact:, Jennifer Tursi, tel +1.610.832.9653; jtursi@astm.org Release #11790 ###
-
ASTM International’s committee on textiles ( D13 ) is developing a proposed standard for writing terminology in textile standards. “This practice is intended to address the importance of a ‘critical building block’ that is used to develop and construct a standard that has value and utility for many years,” says ASTM International member Vince Diaz. “If the terminology is vague or ambiguous, the…, Media Inquiries:, Gavin O’Reilly, tel +1.610.832.9618; goreilly@astm.org, Committee Contact:, Nora Nimmerichter, tel +1.610.832.9815; nnimmerichter@astm.org Release #11656 ###
-
ASTM International’s general aviation aircraft committee ( F44 ) has revised their standard for systems and equipment in aircraft. The newly revised standard ( F3061/F3061M ) covers the systems and equipment aspects of airworthiness and design for aircraft. Topics covered in the standard include electrical systems, environmental requirements, manual and automatic flight controls, and flight data…, Media Inquiries:, Dan Bergels, tel +1.610.832.9602; dbergels@astm.org, Committee Contact:, Joe Koury, tel +1.610.832.9804; jkoury@astm.org Release #11525 ###
-
ASTM International announced today the Journal of Testing and Evaluation, the organization’s flagship journal, received an increased 2021 impact factor rating of 1.333, up 5.5% from the previous year. The impact factor is calculated each year by Clarivate Analytics and given to journals that appear in their database, Science Citation Index. Launched in 1973, the journal is a multi-disciplinary…, Media Inquiries:, Dan Bergels, tel +1.610.832.9602; dbergels@astm.org Release #11472 ###
-
Particle size distribution is an important factor in the manufacture of many products, from cement to perfume. A proposed ASTM International standard ( WK45240 ) will set out a general approach to the particle size distribution measurement of powders, suspensions, or slurries using an appropriate wet or dry methodology by the laser diffraction technique. ASTM’s committee on particle and spray…
-
A proposed ASTM International standard will establish a new practice for determining safe-life, inspection threshold, and reoccurring inspection intervals for airplanes. ASTM International’s general aviation aircraft committee ( F44 ) is developing the proposed standard. According to the U.S. Federal Aviation Administration, the safe-life of a structure is the number of events, such as flights,…, Media Inquiries:, Jaime Martorana, tel +1.610.832.9796; jmartorana@astm.org, Committee Contact:, Joe Koury, tel +1.610.832.9804; jkoury@astm.org Release #11295 ###
-
ASTM International’s autonomy design and operations in aviation administrative committee (AC377) is hosting the 2nd Annual ASTM Autonomy in Aviation Symposium, October 19, 2021, to be held at the Santa Clara Marriott (Santa Clara, California, USA). The objective of the symposium is to facilitate discussions on standards development for aviation autonomy while bringing forward perspectives from…, Media Inquiries:, Jaime Martorana, tel +1.610.832.9796; jmartorana@astm.org Release #11289 ###
-
A proposed ASTM International standard test method will cover the determination of maturity, fineness, ribbon width, and specific surface area (micronaire) of cotton fibers. ASTM International’s textiles committee ( D13 ) is developing the proposed standard. This test method ( WK75782 ) focuses on cotton fibers from a loose, chemically untreated sample taken before harvest, during ginning,…, Media Inquiries:, Jaime Martorana, tel +1.610.832.9796; jmartorana@astm.org, Committee Contact:, Nora Nimmerichter, tel +1.610.832.9815; nnimmerichter@astm.org Release #11267 ###
-
A proposed ASTM International standard would address requirements to evaluate small aircraft components as low stress structures. ASTM’s general aviation aircraft committee ( F44 ) is developing the proposed standard. The proposed standard (WK61232) would address requirements for users to designate aircraft components as low stress structures, allowing the user to forgo certain structural…, Media Inquiries:, Jaime Martorana, tel +1.610.832.9796; jmartorana@astm.org, Committee Contact:, Joe Koury, tel +1.610.832.9804; jkoury@astm.org Release #11263 ###
-
A new ASTM International standard will be helpful in determining load data for small airplanes. ASTM’s general aviation aircraft committee ( F44 ) developed the new standard, which will soon be published as F3498. According to ASTM International member A.K.M. Haque, the new standard will be used by aircraft manufacturers to certify new designs; aircraft repair and modification organizations to…, Media Inquiries:, Jaime Martorana, tel +1.610.832.9796; jmartorana@astm.org , Committee Contact:, Joe Koury, tel +1.610.832.9804; jkoury@astm.org Release #11174 ###