Search
Advanced search
Filter by category
Filter by committee
Search results
-
ASTM International’s particle and spray characterization committee ( E29 ) is developing a proposed standard that will be used to measure physical and chemical properties of nanoparticles in a variety of industrial realms. The standard ( E3427 ) describes how to use laser-amplified detection/power spectrum analysis to measure the number of physical and chemical properties of nanoparticles,…, Media Inquiries:, Gavin O’Reilly, tel +1.610.832.9618; goreilly@astm.org, Committee Contact:, Jennifer Tursi, tel +1.610.832.9653; jtursi@astm.org Release #11790 ###
-
ASTM International’s thermal insulation committee ( C16 ) has approved a new standard that will aid in the development of new insulation products. The new standard ( C1919 ) covers the measurement of steady-state thermal transmission properties of small flat slab thermal insulation specimens using a heat-flow-meter apparatus. ASTM member Phalguni Mukhopadhyaya says that, in addition to being used…, Media Inquiries:, Dan Bergels, tel +1.610.832.9602; dbergels@astm.org, Committee Contact:, Mary Mikolajewski, tel +1.610.832.9678; mmikolajewski@astm.org Release #11619 ###
-
Particle size distribution is an important factor in the manufacture of many products, from cement to perfume. A proposed ASTM International standard ( WK45240 ) will set out a general approach to the particle size distribution measurement of powders, suspensions, or slurries using an appropriate wet or dry methodology by the laser diffraction technique. ASTM’s committee on particle and spray…
-
A new ASTM International standard covers installation techniques for metal jacketing on mechanical insulation systems. ASTM’s thermal insulation committee ( C16 ) developed the new standard, soon to be available as C1879. Metal jacketing is used as the protective cover over pipe and rigid tubing insulation in most outdoor applications, which include oil, gas, petrochemical, pharmaceutical, food/…, Media Inquiries:, Jaime Martorana, tel +1.610.832.9796; jmartorana@astm.org, Committee Contact:, Mary Mikolajewski, tel +1.610.832.9678; mmikolajewski@astm.org Release #11239 ###
-
A proposed ASTM International standard will establish specification requirements for flexible protective jackets made of modified asphalt or butyl rubber. ASTM International’s thermal insulation committee ( C16 ) is developing the proposed standard. Protective jackets guard products such as ducts and pipe insulation against physical abuse as well as, in some cases, the effects of weather. All…, Media Inquiries:, Jaime Martorana, tel+1.610.832.9796; jmartorana@astm.org, Committee Contact:, Mary Mikolajewski, tel+1.610.832.9678; mmikolajewski@astm.org Release #11215 ###
-
ASTM International’s thermal insulation committee ( C16 ) is developing a proposed standard ( WK67790 ) that will help determine the amount of water retained by flat specimens of rigid thermal insulation after immersion and drying. “The proposed test method will allow manufacturers and insulation users to learn more about the wetting and drying behavior of rigid insulations,” says ASTM member…, Media Inquiries:, Jaime Martorana, tel +1.610.832.9796; jmartorana@astm.org , Committee Contact:, Mary Mikolajewski, tel +1.610.832.9678; mmikolajewski@astm.org Release #11179 ###
-
In light of COVID-19 (coronavirus) and growing safety concerns for members and staff, ASTM International announced today that previously scheduled April standards development meetings in Boston (March 29-April 3) and Prague (April 27-30) have been canceled. The decision was based on several factors, including, but not limited to: Continued review of information and recommendations from the U.S.…, Media Inquiries:, Dan Bergels, tel +1.610.832.9602; dbergels@astm.org Release #10993
-
A proposed ASTM International standard aims to help engineers who use water-resistant protective jackets to encase thermal insulation. The organization’s thermal insulation committee ( C16 ) is developing the standard. “These types of protective jackets are installed over pipe, duct, and equipment insulation in both industrial and commercial applications,” says ASTM International member Gordon…, Media Inquiries:, Dan Bergels, tel +1.610.832.9602; dbergels@astm.org, Committee Contact:, Mary Mikolajewski, tel +1.610.832.9678; mmikolajewski@astm.org Release #10985
-
A new ASTM International standard will help manufacturers of particulates, such as sand, gravel, and grit, to better measure their products. According to ASTM International member Paul O’Brien, engineering manager at JM Canty, the new guide explains a way to correlate different types of instruments that measure solid-particle distributions. Using the new standard will help expand the capability…, Media Inquiries:, Dan Bergels, tel +1.610.832.9602; dbergels@astm.org, Committee Contact:, Molly Lynyak, tel +1.610.832.9743; mlynyak@astm.org Release #10674
-
ASTM International’s committee on particle and spray characterization ( E29 ) is working on a new standard that aims to reduce uncertainty from an existing test method (bubble point test) for woven wire filter cloth. The material, also known as Dutch weave, is used for general industrial filtration including separation of solids from fluids. The bubble point test determines the pressure at the…, Media Inquiries:, Dan Bergels, tel +1.610.832.9602; dbergels@astm.org, Committee Contact:, Molly Lynyak, tel +610.832.9743; mlynyak@astm.org Release #10657