Search
Advanced search
Filter by category
Filter by committee
Search results
-
ASTM International’s particle and spray characterization committee ( E29 ) is developing a proposed standard that will be used to measure physical and chemical properties of nanoparticles in a variety of industrial realms. The standard ( E3427 ) describes how to use laser-amplified detection/power spectrum analysis to measure the number of physical and chemical properties of nanoparticles,…, Media Inquiries:, Gavin O’Reilly, tel +1.610.832.9618; goreilly@astm.org, Committee Contact:, Jennifer Tursi, tel +1.610.832.9653; jtursi@astm.org Release #11790 ###
-
A newly proposed standard from, ASTM International’s aircraft systems committee ( F39 ) will cover the design of hybrid-electric powerplants and engines. “This proposed standard is intended to support companies that are creating hybrid-electric power generation systems for use as the primary source of electrical propulsive power in electric aircraft,” says ASTM member David Eichstedt. “They will benefit from a more clearly-…, , Media Inquiries:, Dan Bergels, tel +1.610.832.9602; dbergels@astm.org, Committee Contact:, Joe Koury, tel +1.610.832.9804; jkoury@astm.org Release #11551 ###
-
ASTM International’s metallic-coated iron and steel products committee ( A05 ) is developing a proposed standard that will demonstrate how bend testing can be used to determine how well metallic coatings adhere to steel sheet. ASTM International member Betsy Hoppe says that the proposed test method was initiated after a steel sheet producer with a continuous hot-dip galvanizing line requested a…
-
Particle size distribution is an important factor in the manufacture of many products, from cement to perfume. A proposed ASTM International standard ( WK45240 ) will set out a general approach to the particle size distribution measurement of powders, suspensions, or slurries using an appropriate wet or dry methodology by the laser diffraction technique. ASTM’s committee on particle and spray…
-
ASTM International’s autonomy design and operations in aviation administrative committee (AC377) is hosting the 2nd Annual ASTM Autonomy in Aviation Symposium, October 19, 2021, to be held at the Santa Clara Marriott (Santa Clara, California, USA). The objective of the symposium is to facilitate discussions on standards development for aviation autonomy while bringing forward perspectives from…, Media Inquiries:, Jaime Martorana, tel +1.610.832.9796; jmartorana@astm.org Release #11289 ###
-
Today, global standards developer ASTM International announced the publication of a new technical report on aviation. The report, “Developmental Pillars of Increased Autonomy for Aircraft Systems”, was developed by ASTM’s autonomy design and operations in aviation administrative committee (AC377). The new report is intended to promote the sound application of technical best practices to increase…, Media Inquiries, : Dan Bergels, tel +1.610.832.9602; dbergels@astm.org Release #11054 ###
-
In light of COVID-19 (coronavirus) and ongoing safety concerns for members and staff, ASTM International announced today that all previously scheduled in-person May standards development meetings (including independent meetings) have been canceled. Earlier this month, ASTM International announced the cancellation of all April in-person meetings . These decisions were based on several factors,…, Media Inquiries:, Dan Bergels, tel +1.610.832.9602; dbergels@astm.org Release #11001 ###
-
A new ASTM International standard covers a polymer coating that could provide more durable corrosion protection to infrastructure than zinc coatings. ASTM’s metallic-coated iron and steel products ( A05 ) developed the standard, which will soon be published as A1113. The new standard specifically addresses polymer-coated corrugated steel structural plates used to construct pipe, pipe-arches,…, Media Inquiries:, Dan Bergels, tel +1.610.832.9602; dbergels@astm.org, Committee Contact:, Kristy Straiton, tel +1.610.832.9640; kstraiton@astm.org Release #10999 ###
-
A new ASTM International standard aims to provide direction for constructing mechanically stabilized earth (MSE) walls. “Walls are often needed to retain soil in key places, such as along highways that approach bridge overpasses,” says ASTM International member Roger Brockenbrough of R.L. Brockenbrough and Associates, Inc. “Rather than building a massive cast-in-place wall with extensive…, Media Inquiries:, Dan Bergels, tel +1.610.832.9602; dbergels@astm.org, Committee Contact: , Kristy Straiton, tel +1.610.832.9640; kstraiton@astm.org Release #10878
-
A new ASTM International standard will provide guidance in evaluating aircraft alterations. ASTM International’s aircraft systems committee ( F39 ) approved the standard, which will soon be published as F3361. According to ASTM International member Dale Scheid, an avionics service engineer at Air Methods Corporation, the new standard will help people who need to determine whether changes to…, Media Inquiries:, Dan Bergels, tel +1.610.832.9602; dbergels@astm.org, Committee Contact:, Joe Koury, tel +1.610.832.9804; jkoury@astm.org Release #10705