Search
Advanced search
Filter by category
Filter by committee
Search results
-
Traffic monitoring is a means of counting and classifying vehicles and measuring vehicle flow characteristics, such as vehicle speed, lane occupancy, turning movements and other items typically used to portray traffic movement. In order for traffic monitoring data to be assessed properly, information on how the data were collected, edited, summarized and reported must be provided. This obligation…
-
A new ASTM International standard will provide gasket manufacturers a test for measuring creep and compression that can be used for R&D and material comparisons, and as a quality assurance tool. ASTM F2837 , Test Method for Hot Compression Properties of Gasket Materials, was developed by Subcommittee F03.40 on Chemical Test Methods, under the jurisdiction of ASTM International Committee F03…, ASTM Committee F03 Next Meeting:, Oct 12-13, October Committee Week, San Antonio, Texas, Technical Contact:, James Lingenfelder, Gasket Resources Inc., Houston, Texas, Phone: 713-856-9445; jtling@durlon.com, ASTM Staff Contact:, Joseph Hugo, Phone: 610-832-9740; jhugo@astm.org, ASTM PR Contact:, Barbara Schindler, Phone: 610-832-9603; bschindl@astm.org Release #8695/Sept2010
-
Since the appearance of the first California-type models around 1940, the profilograph has been a popular device used for quality control in the construction of pavements. Both roadway and airfield landing agencies have adopted roughness indexes computed from profilograph-derived measurements as a level of construction quality. Emerging high-speed inertial profilers can now quickly collect…
-
A proposed new standard being developed by ASTM International Committee E17 on Vehicle-Pavement Systems will be the first to describe how truth-in-data should be applied to traffic monitoring data collection, summarization and reporting. WK25280 , Practice for Highway Traffic Monitoring Truth-in-Data, is under the jurisdiction of Subcommittee E17.52 on Traffic Monitoring. Current traffic…
-
Being able to compile and interpret data on how traffic turns through an intersection could have an impact on future environmental and safety decisions regarding intersection geometry and traffic control. However, until recently no standard has existed to properly obtain and use this data. Now, ASTM International Committee E17 on Vehicle-Pavement Systems has approved E2667 , Practice for…
-
No industry standard currently exists that addresses the vacuum sealing requirements of knife-edged flanges for high vacuum applications. Existing international standards focus on interchangeability of the hardware, but do not address the reliability of the seal. ASTM International Committee E42 on Surface Analysis is now working on a proposed standard on the subject, WK21206 , Specification…
-
A 2002 workshop on galling wear held by ASTM International Committee G02 on Wear and Erosion provided the impetus for the development of a new standard, ASTM G196 , Test Method for Galling Resistance of Material Couples. The new standard is under the jurisdiction of Subcommittee G02.40 on Non-Abrasive Wear. According to Scott Hummel, Ph.D., associate professor, head of the department of…
-
ASTM International Committee F03 on Gaskets has developed and approved a new standard that can be used to evaluate gasket materials covered by ASTM F104 , Classification System for Nonmetallic Gasket Materials. The new standard, F2716 , Practice for Comparison of Nonmetallic Flat Gaskets in High Pressure Saturated Steam, is under the jurisdiction of Subcommittee F03.10 on Composite Gaskets. ASTM…
-
A new ASTM International standard responds to a recent emphasis by regulatory agencies that firms manufacturing drug products demonstrate the efficacy of disinfectants used in controlled environments. The standard, ASTM E2614 , Guide for Evaluation of Cleanroom Disinfectants, was developed by Subcommittee E35.15 on Antimicrobial Agents, part of ASTM International Committee E35 on Pesticides and…
-
Drawing on the best practices of the U.S. Federal Highway Administration and the states, ASTM International Committee E17 on Vehicle-Pavement Systems has developed a new standard, E 2561 , Practice for Installation of Inductive Loop Detectors. E 2561 is under the jurisdiction of Subcommittee E17.52 on Traffic Monitoring. Inductive loop detectors are installed in sawed slots in roadway pavement…