Search
Advanced search
Filter by category
Filter by committee
Search results
-
ASTM International has launched a new technical committee, F45 on Driverless Automatic Guided Industrial Vehicles . After organizational meetings in October 2013 and January 2014, F45 was approved at the board of director’s recent spring meeting. In use since 1953, automated guided vehicles (AGVs) are defined by the Material Handling Institute (MHI) as “computer-controlled wheel-based load…, Technical Contact:, Roger Bostelman, National Institute of Standards and Technology, Gaithersburg, Md., roger.bostelman@nist.gov , ASTM Staff Contact:, Pat Picariello, Phone: 610-832-9720; ppicariello@astm.org, ASTM PR Contact:, Barbara Schindler, Phone: 610-832-9603; bschindl@astm.org Release #9650
-
Bisphenol A, or BPA, is a high production volume chemical widely used in manufacturing polycarbonate plastics and epoxy resins that are used in many industries. Procedures described in a new ASTM International standard will be used for measuring BPA concentration in environmental media such as soils, sludges and biosolids. The new standard, ASTM D7858 , Test Method for Determination of Bisphenol…, ASTM Committee D34 Next Meeting:, Virtual meeting, Oct. 10-11, 2013, Technical Contact:, Lawrence Zintek, Ph.D., U.S. Environmental Protection Agency, Region 5 Chicago Regional Laboratory, Chicago, Ill., Phone: 312-886-2925; zintek.lawrence@epa.gov, ASTM Staff Contact:, Alyson Fick, Phone: 610-832-9710; afick@astm.org, ASTM PR Contact:, Barbara Schindler, Phone: 610-832-9603; bschindl@astm.org Release #9456
-
A new ASTM subcommittee will develop proposed standards to analyze organic compounds discharged into sanitary sewers. Subcommittee D34.02 on Discharge of Organic Wastes into Sanitary Sewers is part of ASTM International Committee D34 on Waste Management . “Considering the need for low detection limits and measurements that would assure all of the compounds of interest have been measured, sanitary…, ASTM Committee D34 Next Meeting:, April 2-3, 2013, EPA Headquarters, Las Vegas, Nev., Technical Contact:, John E. Burnett, Department of Public Works of Baltimore County, Columbia, Md., Phone: 410-887-5488; jeburnett@baltimorecountymd, ASTM Staff Contact:, Alyson Fick, Phone: 610-832-9710; afick@astm.org , ASTM PR Contact:, Barbara Schindler, Phone: 610-832-9603; bschindl@astm.org Release #9331
-
While the quality of coating materials for buried pipe at nuclear power plants has evolved over time, there is currently no written standard that would allow plants to fully take advantage of advances in coating technology. A proposed new standard will provide coating guidance for plants seeking to repair or replace buried pipe. The proposed standard, ASTM WK36282 , Guide for Selection of Coating…
-
ASTM International Committee F16 on Fasteners has recently approved an important new standard that deals with coated threaded fasteners and washers by hot-dip zinc galvanizing. The standard, F 2329, Specification for Zinc Coating, Hot-Dip, Requirements for Application to Carbon and Alloy Steel Bolts, Screws, Washers, Nuts and Special Threaded Fasteners, is under the jurisdiction of Subcommittee…
-
ASTM International Committee F16 on Fasteners has developed a new standard, F 2329, Specification for Zinc Coating, Hot-Dip, Requirements for Application to Carbon and Alloy Steel Bolts, Screws, Washers, Nuts, and Special Threaded Fasteners. The standard, which is under the jurisdiction of Subcommittee F16.03 on Coatings on Fasteners, covers the requirements for hot-dip zinc coating applied to…
-
ASTM International Committee D33 on Protective Clothing and Lining Work for Power Generation Facilities has approved a revision to standard D 4260, now titled Practice for Liquid and Gelled Acid Etching of Concrete. The revised standard is under the jurisdiction of Subcommittee D33.05 on Application and Surface Preparation. According to Tamryn Doolan, president and CEO, Surface Gel Tek, the…