Search
Advanced search
Filter by category
Filter by committee
Search results
-
Bisphenol A, or BPA, is a high production volume chemical widely used in manufacturing polycarbonate plastics and epoxy resins that are used in many industries. Procedures described in a new ASTM International standard will be used for measuring BPA concentration in environmental media such as soils, sludges and biosolids. The new standard, ASTM D7858 , Test Method for Determination of Bisphenol…, ASTM Committee D34 Next Meeting:, Virtual meeting, Oct. 10-11, 2013, Technical Contact:, Lawrence Zintek, Ph.D., U.S. Environmental Protection Agency, Region 5 Chicago Regional Laboratory, Chicago, Ill., Phone: 312-886-2925; zintek.lawrence@epa.gov, ASTM Staff Contact:, Alyson Fick, Phone: 610-832-9710; afick@astm.org, ASTM PR Contact:, Barbara Schindler, Phone: 610-832-9603; bschindl@astm.org Release #9456
-
A new ASTM subcommittee will develop proposed standards to analyze organic compounds discharged into sanitary sewers. Subcommittee D34.02 on Discharge of Organic Wastes into Sanitary Sewers is part of ASTM International Committee D34 on Waste Management . “Considering the need for low detection limits and measurements that would assure all of the compounds of interest have been measured, sanitary…, ASTM Committee D34 Next Meeting:, April 2-3, 2013, EPA Headquarters, Las Vegas, Nev., Technical Contact:, John E. Burnett, Department of Public Works of Baltimore County, Columbia, Md., Phone: 410-887-5488; jeburnett@baltimorecountymd, ASTM Staff Contact:, Alyson Fick, Phone: 610-832-9710; afick@astm.org , ASTM PR Contact:, Barbara Schindler, Phone: 610-832-9603; bschindl@astm.org Release #9331
-
While the quality of coating materials for buried pipe at nuclear power plants has evolved over time, there is currently no written standard that would allow plants to fully take advantage of advances in coating technology. A proposed new standard will provide coating guidance for plants seeking to repair or replace buried pipe. The proposed standard, ASTM WK36282 , Guide for Selection of Coating…
-
ASTM International Committee D27 on Electrical Insulating Liquids and Gases is continuing its work on standards for natural esters with the development of a proposed new standard, WK21616 , Test Method for Oxidation Induction Time of Natural Ester Insulating Fluids by Pressure (PDSC) or Regular Differential Scanning Calorimetry (DSC). The proposed standard was submitted under the jurisdiction of…
-
ASTM International Committee F16 on Fasteners has recently approved an important new standard that deals with coated threaded fasteners and washers by hot-dip zinc galvanizing. The standard, F 2329, Specification for Zinc Coating, Hot-Dip, Requirements for Application to Carbon and Alloy Steel Bolts, Screws, Washers, Nuts and Special Threaded Fasteners, is under the jurisdiction of Subcommittee…
-
During the past five years, certain insulating oils have been found to contain corrosive sulfur that can produce copper sulfide deposits as a function of time and temperature in operating equipment. A proposed revision to ASTM standard D 1275, Test Method for Corrosive Sulfur in Electrical Insulating Oils, will provide a means to certify that new or in service oils either contain or do not…
-
ASTM International will launch a new Proficiency Testing Program (PTP) on Dissolved Gas Analyses (DGA) of In-Service Insulating Fluid in February 2006. The program will be offered to laboratories who need a statistical quality assurance tool that will enable them to improve and maintain a high level of performing ASTM standard D 3612, Test Method for Analysis of Gases Dissolved in Electrical…
-
ASTM International Committee F16 on Fasteners has developed a new standard, F 2329, Specification for Zinc Coating, Hot-Dip, Requirements for Application to Carbon and Alloy Steel Bolts, Screws, Washers, Nuts, and Special Threaded Fasteners. The standard, which is under the jurisdiction of Subcommittee F16.03 on Coatings on Fasteners, covers the requirements for hot-dip zinc coating applied to…
-
ASTM International Committee D33 on Protective Clothing and Lining Work for Power Generation Facilities has approved a revision to standard D 4260, now titled Practice for Liquid and Gelled Acid Etching of Concrete. The revised standard is under the jurisdiction of Subcommittee D33.05 on Application and Surface Preparation. According to Tamryn Doolan, president and CEO, Surface Gel Tek, the…