Search
Advanced search
Filter by category
Filter by committee
Search results
-
Traffic monitoring is a means of counting and classifying vehicles and measuring vehicle flow characteristics, such as vehicle speed, lane occupancy, turning movements and other items typically used to portray traffic movement. In order for traffic monitoring data to be assessed properly, information on how the data were collected, edited, summarized and reported must be provided. This obligation…
-
The ongoing focus on sustainability in construction has contributed to greater interest in vegetative, or green, roof systems, in which traditional roofing material is replaced or supplemented with vegetation. A proposed new ASTM International standard will address an important aspect of designing this kind of roofing: determining the proper roofing and waterproofing membrane for a particular…
-
Since the appearance of the first California-type models around 1940, the profilograph has been a popular device used for quality control in the construction of pavements. Both roadway and airfield landing agencies have adopted roughness indexes computed from profilograph-derived measurements as a level of construction quality. Emerging high-speed inertial profilers can now quickly collect…
-
A proposed new standard being developed by ASTM International Committee E17 on Vehicle-Pavement Systems will be the first to describe how truth-in-data should be applied to traffic monitoring data collection, summarization and reporting. WK25280 , Practice for Highway Traffic Monitoring Truth-in-Data, is under the jurisdiction of Subcommittee E17.52 on Traffic Monitoring. Current traffic…
-
ASTM International Subcommittee E34.50 on Health and Safety Standards for Metalworking Fluids has developed three new standards. Two of the recently approved ASTM standards cover aspects of water-miscible metalworking fluids, while the third concerns prevention of dermatitis in the wet metal removal fluid environment., Prevention of Dermatitis, Dermatitis is an inflammatory response of the skin to a chemical or physical agent. While redness, swelling and itching are typical signs of dermatitis, symptoms can be more severe as well. A new ASTM standard, ASTM E2693 , Practice for Prevention of Dermatitis in the Wet Metal Removal Fluid Environment, discusses dermatitis and its causes and presents a comprehensive approach to dermatitis…, Metalworking Fluids, Two new E34.50 standards address the detection of microbial contamination in metalworking fluids: ASTM E2657 , Test Method for Determination of Endotoxin Concentrations in Water-Miscible Metalworking Fluids, and ASTM E2694 , Test Method for Measurement of Adenosine Triphosphate in Water-Miscible Metalworking Fluids. Both ASTM E2657 and ASTM E2694 measure biological contamination in metalworking…, Participation Invited, The subcommittee is currently looking for participants for an interlaboratory study for ASTM E2657 and ASTM E2694 . “We plan to use a single set of MWF for both standards, so labs who are interested in either or both are welcome to participate,” says Passman. “A few labs will run both the ILS’s for both standards, while most will run one or the other.” Subcommittee E34.50 is part of ASTM…
-
Being able to compile and interpret data on how traffic turns through an intersection could have an impact on future environmental and safety decisions regarding intersection geometry and traffic control. However, until recently no standard has existed to properly obtain and use this data. Now, ASTM International Committee E17 on Vehicle-Pavement Systems has approved E2667 , Practice for…
-
When fasteners penetrate roofing or waterproofing products as a planned part of installation, it is expected in some cases that the product will resist water migration at the point of penetration. A new ASTM International standard, D7349 , Test Method for Determining the Capability of Roofing and Waterproofing Materials to Seal Around Fasteners, addresses this situation. ASTM D7349 was developed…
-
Modified bitumen products have been in use since the mid-1970s, and represent a substantial percentage of the commercial asphalt roofs installed throughout North America. A new ASTM International standard addresses the use of cold process adhesives in modified bitumen roofing systems. ASTM D7379 , Test Methods for Strength of Modified Bitumen Sheet Material Laps Using Cold Process Adhesive, was…
-
All interested parties in the glass industry are invited to participate in the development of a proposed new standard guide for the safe handling of annealed glass. The new standard will be developed by a task group within ASTM Committee E34 on Occupational Health and Safety. A small group from industry and OSHA met in Rossford, Ohio, in March to discuss this new activity. The task group plans to…
-
Information and product destruction services is a rapidly growing industry. In order to develop standards to serve the needs of this industry, ASTM International Committee E34 on Occupational Health and Safety has formed Subcommittee E34.25 on Mobile and Plant-Based Security Destruction Equipment Safety Requirements. All interested parties are invited to participate in the standards developing…