Search
Advanced search
Filter by category
Filter by committee
Search results
-
The measurement of acid mist is becoming increasingly important due to recent actions taken by the U.S. Environmental Protection Agency on fine particles (2.5 micrometers in diameter and smaller) that are unhealthy to breathe. ASTM International Committee D22 on Air Quality is currently working on a proposed standard for measuring acid mists that come from combustion sources, WK22846 , Test…
-
ASTM International Committee D27 on Electrical Insulating Liquids and Gases is continuing its work on standards for natural esters with the development of a proposed new standard, WK21616 , Test Method for Oxidation Induction Time of Natural Ester Insulating Fluids by Pressure (PDSC) or Regular Differential Scanning Calorimetry (DSC). The proposed standard was submitted under the jurisdiction of…
-
When fasteners penetrate roofing or waterproofing products as a planned part of installation, it is expected in some cases that the product will resist water migration at the point of penetration. A new ASTM International standard, D7349 , Test Method for Determining the Capability of Roofing and Waterproofing Materials to Seal Around Fasteners, addresses this situation. ASTM D7349 was developed…
-
Modified bitumen products have been in use since the mid-1970s, and represent a substantial percentage of the commercial asphalt roofs installed throughout North America. A new ASTM International standard addresses the use of cold process adhesives in modified bitumen roofing systems. ASTM D7379 , Test Methods for Strength of Modified Bitumen Sheet Material Laps Using Cold Process Adhesive, was…
-
A new ASTM International standard provides guidance for using data generated by ASTM standards in testing for asbestos in surface dust. ASTM D 7390 , Guide for Evaluating Asbestos in Dust on Surfaces by Comparison Between Two Environments, was approved by ASTM International Committee D22 on Air Quality, part of Subcommittee D22.07 on Sampling and Analysis of Asbestos. According to James Millette…
-
A new ASTM International standard will provide a method to consistently address indoor air quality complaints in residential buildings and to guide IAQ investigations in an efficient manner. The standard, D 7297 , Practice for Evaluating Residential Indoor Air Quality Concerns, is under the jurisdiction of Subcommittee D22.05 on Indoor Air, part of ASTM International Committee D22 on Air Quality…
-
Laboratories that measure fibers in workplace samples will be the most likely users of two new ASTM International standards: D 7200 , Practice for Sampling and Counting Airborne Fibers, Including Asbestos Fibers, in Mines and Quarries, by Phase Contrast Microscopy and Transmission Electron Microscope; and D 7201 , Practice for Sampling and Counting Airborne Fibers, Including Asbestos Fibers, in…
-
ASTM International Committee F16 on Fasteners has recently approved an important new standard that deals with coated threaded fasteners and washers by hot-dip zinc galvanizing. The standard, F 2329, Specification for Zinc Coating, Hot-Dip, Requirements for Application to Carbon and Alloy Steel Bolts, Screws, Washers, Nuts and Special Threaded Fasteners, is under the jurisdiction of Subcommittee…
-
During the past five years, certain insulating oils have been found to contain corrosive sulfur that can produce copper sulfide deposits as a function of time and temperature in operating equipment. A proposed revision to ASTM standard D 1275, Test Method for Corrosive Sulfur in Electrical Insulating Oils, will provide a means to certify that new or in service oils either contain or do not…
-
ASTM International will launch a new Proficiency Testing Program (PTP) on Dissolved Gas Analyses (DGA) of In-Service Insulating Fluid in February 2006. The program will be offered to laboratories who need a statistical quality assurance tool that will enable them to improve and maintain a high level of performing ASTM standard D 3612, Test Method for Analysis of Gases Dissolved in Electrical…