Search
Advanced search
Filter by category
Filter by committee
Search results
-
A newly approved standard, ASTM D7338 , Guide for the Assessment of Fungal Growth in Buildings, has been developed to provide a go-to reference for anyone testing for mold in buildings. The new standard was developed by Subcommittee D22.08 on Sampling and Analysis of Mold, part of ASTM International Committee D22 on Air Quality. “The lack of consensus standards in the fungal sampling and analysis…, ASTM Committee D22 Next Meeting:, April 10-13, April Committee Week, Anaheim, Calif., Technical Contact:, Lisa Rogers, Mycometer, Inc., Tampa, Fla., Phone: 813-831-6511; lrogers@mycometer.com, ASTM Staff Contact:, David Bradley, Phone: 610-832-9681; dbradley@astm.org, ASTM PR Contact:, Barbara Schindler, Phone: 610-832-9603; bschindl@astm.org Release #8788
-
Two new ASTM International standards on rescue litters and fixed anchorages will contribute to the safety and efficiency of search and rescue operations. Both standards were developed by Subcommittee F32.01 on Equipment, Testing and Maintenance, part of ASTM International Committee F32 on Search and Rescue., BASKET TYPE RESCUE LITTERS, Until the development of ASTM F2821 , Test Methods for Basket Type Rescue Litters, there had not been a standardized means for manufacturers to test these rescue devices, according to John McKently, Los Angeles County Sheriff's Department, and an F32 member. “ASTM F2821 was developed because there was no standard available that allowed manufacturers to test litter products in the same way,” says…, FIXED ANCHORAGES, According to McKently, the impetus for the development of ASTM F2822 , Specification for Fixed Anchorages Installed on Structures Used for Rope Rescue Training, was similar to that of ASTM F2821. In this case, the standard was developed to provide minimum strength requirements for anchorages permanently installed or attached to training towers or other structures used for rope rescue training. “…, ASTM Committee F32 Next Meeting:, Nov. 7-10, in conjunction with the International Technical Rescue Symposium, Golden, Colo., Technical Contact:, John McKently, Los Angeles County Sheriff's Department, Glendale, Calif., Phone: 818-247-3209; jmckently@earthlink.net, ASTM Staff Contact:, Thomas O'Toole, Phone: 610-832-9739; totoole@astm.org, ASTM PR Contact:, Barbara Schindler, Phone: 610-832-9603; bschindl@astm.org Release #8654
-
Air permits from regulatory agencies, such as the U.S. Environmental Protection Agency (USEPA), often require the measurement of a plume's opacity as the plume is emitted from a stationary point source (for example, smokestacks) in the outdoor ambient environment. While such opacity is often visually measured by human observers as “certified smoke readers,” an opacity measurement method using…
-
ASTM International Subcommittee E34.50 on Health and Safety Standards for Metalworking Fluids has developed three new standards. Two of the recently approved ASTM standards cover aspects of water-miscible metalworking fluids, while the third concerns prevention of dermatitis in the wet metal removal fluid environment., Prevention of Dermatitis, Dermatitis is an inflammatory response of the skin to a chemical or physical agent. While redness, swelling and itching are typical signs of dermatitis, symptoms can be more severe as well. A new ASTM standard, ASTM E2693 , Practice for Prevention of Dermatitis in the Wet Metal Removal Fluid Environment, discusses dermatitis and its causes and presents a comprehensive approach to dermatitis…, Metalworking Fluids, Two new E34.50 standards address the detection of microbial contamination in metalworking fluids: ASTM E2657 , Test Method for Determination of Endotoxin Concentrations in Water-Miscible Metalworking Fluids, and ASTM E2694 , Test Method for Measurement of Adenosine Triphosphate in Water-Miscible Metalworking Fluids. Both ASTM E2657 and ASTM E2694 measure biological contamination in metalworking…, Participation Invited, The subcommittee is currently looking for participants for an interlaboratory study for ASTM E2657 and ASTM E2694 . “We plan to use a single set of MWF for both standards, so labs who are interested in either or both are welcome to participate,” says Passman. “A few labs will run both the ILS’s for both standards, while most will run one or the other.” Subcommittee E34.50 is part of ASTM…
-
ASTM International Committee F32 on Search and Rescue is currently developing a number of proposed new standards. Two of the proposed standards under the jurisdiction of Subcommittee F32.02 on Management and Operations are WK23984 , Guide for Level 1 (Basic) Mounted Search and Rescue (MSAR) Responder, and WK24699, Guide for Training for Land SAR as a Level 1 Out of Area Disaster Responder.…
-
The measurement of acid mist is becoming increasingly important due to recent actions taken by the U.S. Environmental Protection Agency on fine particles (2.5 micrometers in diameter and smaller) that are unhealthy to breathe. ASTM International Committee D22 on Air Quality is currently working on a proposed standard for measuring acid mists that come from combustion sources, WK22846 , Test…
-
The importance of telecommunicators in the search and rescue field cannot be overstated. Dispatchers receiving and delivering accurate information in a timely manner are critical to any SAR operation. A new standard developed by ASTM International Committee F32 on Search and Rescue highlights the importance of proper training for SAR dispatchers. The standard, ASTM F2662 , Guide for Minimum…
-
All interested parties in the glass industry are invited to participate in the development of a proposed new standard guide for the safe handling of annealed glass. The new standard will be developed by a task group within ASTM Committee E34 on Occupational Health and Safety. A small group from industry and OSHA met in Rossford, Ohio, in March to discuss this new activity. The task group plans to…
-
A new ASTM International standard provides guidance for using data generated by ASTM standards in testing for asbestos in surface dust. ASTM D 7390 , Guide for Evaluating Asbestos in Dust on Surfaces by Comparison Between Two Environments, was approved by ASTM International Committee D22 on Air Quality, part of Subcommittee D22.07 on Sampling and Analysis of Asbestos. According to James Millette…
-
Information and product destruction services is a rapidly growing industry. In order to develop standards to serve the needs of this industry, ASTM International Committee E34 on Occupational Health and Safety has formed Subcommittee E34.25 on Mobile and Plant-Based Security Destruction Equipment Safety Requirements. All interested parties are invited to participate in the standards developing…