Search
Advanced search
Filter by category
Filter by committee
Search results
-
On July 29, 2011, the U.S. Federal Aviation Administration announced in the Federal Register the availability of ASTM International standard F2746–09 , Specification for Pilot’s Operating Handbook (POH) for Light Sport Airplane, as well as ASTM F2245-10c , Specification for Design and Performance of a Light Sport Airplane. Manufacturers of fixed wing light sport aircraft are required to revise…
-
A new ASTM International practice provides a standard for preparing a mixture of cement paste that will simulate the shearing experienced by the cement paste in concrete. The new standard, ASTM C1738 , Practice for High-Shear Mixing of Hydraulic Cement Pastes, was developed by Subcommittee C01.22 on Workability , part of ASTM International Committee C01 on Cement . According to Chiara Ferraris,…
-
A new ASTM International standard will be used to aid in the creation of auditing programs within the light sport aircraft industry. ASTM F2839 , Practice for Compliance Audits to ASTM Standards on Light Sport Aircraft, was developed by Subcommittee F37.70 on Cross Cutting , part of ASTM International Committee F37 on Light Sport Aircraft . The new practice specifies the minimum methods and…
-
A new ASTM International subcommittee has been created to develop standards that will be meaningful and accurate performance indicators to measure work-related injury and illness performance throughout the world. Subcommittee E34.55 on Occupational Safety and Health Performance Improvement is under the jurisdiction of ASTM International Committee E34 on Occupational Health and Safety. “Measuring…
-
ASTM International Subcommittee E34.50 on Health and Safety Standards for Metalworking Fluids has developed three new standards. Two of the recently approved ASTM standards cover aspects of water-miscible metalworking fluids, while the third concerns prevention of dermatitis in the wet metal removal fluid environment., Prevention of Dermatitis, Dermatitis is an inflammatory response of the skin to a chemical or physical agent. While redness, swelling and itching are typical signs of dermatitis, symptoms can be more severe as well. A new ASTM standard, ASTM E2693 , Practice for Prevention of Dermatitis in the Wet Metal Removal Fluid Environment, discusses dermatitis and its causes and presents a comprehensive approach to dermatitis…, Metalworking Fluids, Two new E34.50 standards address the detection of microbial contamination in metalworking fluids: ASTM E2657 , Test Method for Determination of Endotoxin Concentrations in Water-Miscible Metalworking Fluids, and ASTM E2694 , Test Method for Measurement of Adenosine Triphosphate in Water-Miscible Metalworking Fluids. Both ASTM E2657 and ASTM E2694 measure biological contamination in metalworking…, Participation Invited, The subcommittee is currently looking for participants for an interlaboratory study for ASTM E2657 and ASTM E2694 . “We plan to use a single set of MWF for both standards, so labs who are interested in either or both are welcome to participate,” says Passman. “A few labs will run both the ILS’s for both standards, while most will run one or the other.” Subcommittee E34.50 is part of ASTM…
-
Rapid hardening hydraulic cements are used in a variety of applications in which reduced cementitious contents are desired or early service is needed. Included among these applications are paving, construction, stucco, mortar and block. A newly approved ASTM International standard covering these cements, ASTM C1600/C1600M , Specification for Rapid Hardening Hydraulic Cement, has been developed by…, Type URH, —ultra rapid hardening, for use where ultra high early strength is desired;, Type VRH, —very rapid hardening, for use where very high early strength is desired;, Type MRH, —medium rapid hardening, for use where mid-range rapid hardening, high early strength is desired; and, Type GRH, —general rapid hardening, for use when the higher strength properties of Type VRH or a Type MRH cement is not required. “ASTM C1600 lists minimum requirements for compressive strength, setting time, shrinkage and soundness (autoclave expansion),” says Hicks. “Optional specifications for sulfate expansion, alkali silicate reactions with aggregates, heat of hydration and expansion in water are also…
-
ASTM International Committee F37 on Light Sport Aircraft is currently at work on a proposed new standard that will aid light sport aircraft manufacturers in understanding the standardization system that governs their products. ASTM WK22124 , Guide for Compliance with Light Sport Airplane Standards, is under the jurisdiction of the F37.20 Airplane subcommittee. According to Thomas Gunnarson, U.S.…
-
ASTM International Committee F37 on Light Sport Aircraft will meet March 30 to April 1, 2009, at the Messe Friedrichshafen Exhibition Grounds in Friedrichshafen, Germany, in conjunction with AERO Friedrichshafen 2009. The three days of F37 technical meetings will include discussions on changes to key LSA standards and proposals for new documents. It will also include several other activities,…
-
All interested parties in the glass industry are invited to participate in the development of a proposed new standard guide for the safe handling of annealed glass. The new standard will be developed by a task group within ASTM Committee E34 on Occupational Health and Safety. A small group from industry and OSHA met in Rossford, Ohio, in March to discuss this new activity. The task group plans to…
-
A recently approved revision to ASTM International standard C 150 , Specification for Portland Cement, includes three significant technical changes to the document. The changes are part of a joint effort between ASTM and the American Association of State and Highway and Transportation Officials to harmonize C 150 with AASHTO’s standard, M 85, Specification for Portland Cement. C 150 is under the…