Search
Advanced search
Filter by category
Filter by committee
Search results
-
A new ASTM International subcommittee has been created to develop standards that will be meaningful and accurate performance indicators to measure work-related injury and illness performance throughout the world. Subcommittee E34.55 on Occupational Safety and Health Performance Improvement is under the jurisdiction of ASTM International Committee E34 on Occupational Health and Safety. “Measuring…
-
Interlocking concrete pavements are extensively used in low-speed urban and rural roads throughout Europe and are seeing increased use as an alternative to asphalt and cast-in-place concrete in the United States. A proposed new ASTM International standard will address the management by city and county transportation agencies of roads made from interlocking concrete pavements. The proposed new…, ASTM Committee E17 Next Meeting:, June 5-6, 2011, State College, Pa., Technical Contact:, David R. Smith, Interlocking Concrete Pavement Institute, Herndon, Va., Phone: 703-657-6900, ext. 201; dsmith@icpi.org, ASTM Staff Contact:, Daniel Smith, Phone: 610-832-9727; dsmith@astm.org, ASTM PR Contact:, Barbara Schindler, Phone: 610-832-9603; bschindl@astm.org Release #8857
-
Traffic monitoring is a means of counting and classifying vehicles and measuring vehicle flow characteristics, such as vehicle speed, lane occupancy, turning movements and other items typically used to portray traffic movement. In order for traffic monitoring data to be assessed properly, information on how the data were collected, edited, summarized and reported must be provided. This obligation…
-
Since the appearance of the first California-type models around 1940, the profilograph has been a popular device used for quality control in the construction of pavements. Both roadway and airfield landing agencies have adopted roughness indexes computed from profilograph-derived measurements as a level of construction quality. Emerging high-speed inertial profilers can now quickly collect…
-
A proposed new standard being developed by ASTM International Committee E17 on Vehicle-Pavement Systems will be the first to describe how truth-in-data should be applied to traffic monitoring data collection, summarization and reporting. WK25280 , Practice for Highway Traffic Monitoring Truth-in-Data, is under the jurisdiction of Subcommittee E17.52 on Traffic Monitoring. Current traffic…
-
ASTM International Subcommittee E34.50 on Health and Safety Standards for Metalworking Fluids has developed three new standards. Two of the recently approved ASTM standards cover aspects of water-miscible metalworking fluids, while the third concerns prevention of dermatitis in the wet metal removal fluid environment., Prevention of Dermatitis, Dermatitis is an inflammatory response of the skin to a chemical or physical agent. While redness, swelling and itching are typical signs of dermatitis, symptoms can be more severe as well. A new ASTM standard, ASTM E2693 , Practice for Prevention of Dermatitis in the Wet Metal Removal Fluid Environment, discusses dermatitis and its causes and presents a comprehensive approach to dermatitis…, Metalworking Fluids, Two new E34.50 standards address the detection of microbial contamination in metalworking fluids: ASTM E2657 , Test Method for Determination of Endotoxin Concentrations in Water-Miscible Metalworking Fluids, and ASTM E2694 , Test Method for Measurement of Adenosine Triphosphate in Water-Miscible Metalworking Fluids. Both ASTM E2657 and ASTM E2694 measure biological contamination in metalworking…, Participation Invited, The subcommittee is currently looking for participants for an interlaboratory study for ASTM E2657 and ASTM E2694 . “We plan to use a single set of MWF for both standards, so labs who are interested in either or both are welcome to participate,” says Passman. “A few labs will run both the ILS’s for both standards, while most will run one or the other.” Subcommittee E34.50 is part of ASTM…
-
Rapid hardening hydraulic cements are used in a variety of applications in which reduced cementitious contents are desired or early service is needed. Included among these applications are paving, construction, stucco, mortar and block. A newly approved ASTM International standard covering these cements, ASTM C1600/C1600M , Specification for Rapid Hardening Hydraulic Cement, has been developed by…, Type URH, —ultra rapid hardening, for use where ultra high early strength is desired;, Type VRH, —very rapid hardening, for use where very high early strength is desired;, Type MRH, —medium rapid hardening, for use where mid-range rapid hardening, high early strength is desired; and, Type GRH, —general rapid hardening, for use when the higher strength properties of Type VRH or a Type MRH cement is not required. “ASTM C1600 lists minimum requirements for compressive strength, setting time, shrinkage and soundness (autoclave expansion),” says Hicks. “Optional specifications for sulfate expansion, alkali silicate reactions with aggregates, heat of hydration and expansion in water are also…
-
Being able to compile and interpret data on how traffic turns through an intersection could have an impact on future environmental and safety decisions regarding intersection geometry and traffic control. However, until recently no standard has existed to properly obtain and use this data. Now, ASTM International Committee E17 on Vehicle-Pavement Systems has approved E2667 , Practice for…
-
All interested parties in the glass industry are invited to participate in the development of a proposed new standard guide for the safe handling of annealed glass. The new standard will be developed by a task group within ASTM Committee E34 on Occupational Health and Safety. A small group from industry and OSHA met in Rossford, Ohio, in March to discuss this new activity. The task group plans to…
-
A recently approved revision to ASTM International standard C 150 , Specification for Portland Cement, includes three significant technical changes to the document. The changes are part of a joint effort between ASTM and the American Association of State and Highway and Transportation Officials to harmonize C 150 with AASHTO’s standard, M 85, Specification for Portland Cement. C 150 is under the…