Search
Advanced search
Filter by category
Filter by committee
Search results
-
A new ASTM International practice provides a standard for preparing a mixture of cement paste that will simulate the shearing experienced by the cement paste in concrete. The new standard, ASTM C1738 , Practice for High-Shear Mixing of Hydraulic Cement Pastes, was developed by Subcommittee C01.22 on Workability , part of ASTM International Committee C01 on Cement . According to Chiara Ferraris,…
-
Laboratories that have the ability to analyze titanium and titanium alloys by spark-atomic emission spectrometry or glow discharge-AES are currently being sought to participate in an interlaboratory study for a proposed new standard. ASTM WK25738 , Test Method for Analysis of Titanium and Titanium Alloys by Spark-Atomic Emission/Glow Discharge-Atomic Emission Spectrometry, is currently being…, ASTM Committee E01 Next Meeting:, May 15-18, 2011, May Committee Week, Anaheim, Calif., Technical Contact:, Kevin VonScio, Perryman Co., Houston, Pa., Phone: 724-746-9390; kvonscio@perrymanco.com, ASTM Staff Contact:, Thomas O’Toole, Phone: 610-832-9739; totoole@astm.org, ASTM PR Contact:, Barbara Schindler, Phone: 610-832-9603; bschindl@astm.org Release #8855
-
New regulations set forth by the U.S. Environmental Protection Agency to mandate greenhouse gas reporting in the U.S. carbon black industry have led to the development of a new ASTM International standard, ASTM D7662 , Test Method for Carbon Content in Carbon Black Feedstock Oils. ASTM D7662 is under the jurisdiction of Subcommittee D24.66 on Environment, Health and Safety, part of ASTM…
-
The U.S. Environmental Protection Agency has set forth new regulations that mandate greenhouse gas reporting in the U.S. carbon black industry. These regulations were the impetus for the development of a new ASTM International standard, ASTM D7633 , Test Method for Carbon Black Carbon Content. The new standard was developed by Subcommittee D24.66 on Environment, Health and Safety, part of ASTM…, ASTM Committee D24 Next Meeting:, Dec. 6-8, December Committee Week, New Orleans, La., Technical Contact:, George Joyce, Columbian Chemicals Co., Marietta, Ga., Phone: 770-792-9467; gjoyce@columbianchemicals.com, ASTM Staff Contact:, Joe Koury, Phone: 610-832-9804; jkoury@astm.org, ASTM PR Contact:, Barbara Schindler, Phone: 610-832-9603; bschindl@astm.org Release #8641
-
Trona, or sodium sesquicarbonate, is a fine mineral powder that has proven to be effective at removing acid gases from air emissions. While trona can be a useful component of air pollution control systems, it can be difficult to handle, particularly when moisture is present. A proposed new ASTM standard will present a repeatable, precise and accurate test method for analyzing moisture levels in…, ASTM Committee E01 Next Meeting:, Nov. 14-17, November Committee Week, San Antonio, Texas, Technical Contact: J, ames D. Phillip, Solvay Chemicals Inc, Green River, Wyo., Phone: 307-872-6519; jim.phillip@solvay.com, ASTM Staff Contact:, Thomas O'Toole, Phone: 610-832-9739; totoole@astm.org, ASTM PR Contact:, Barbara Schindler, Phone: 610-832-9603; bschindl@astm.org Release #8608
-
An increased interest in the polyaromatic hydrocarbon content of carbon black, particularly in Europe, and new U.S. Environmental Protection Agency requirements to report greenhouse gas emissions from U.S. industry including carbon black plants has led to the formation of a new ASTM subcommittee. Subcommittee D24.66 on Environment, Health and Safety is part of ASTM International Committee D24 on…
-
Rapid hardening hydraulic cements are used in a variety of applications in which reduced cementitious contents are desired or early service is needed. Included among these applications are paving, construction, stucco, mortar and block. A newly approved ASTM International standard covering these cements, ASTM C1600/C1600M , Specification for Rapid Hardening Hydraulic Cement, has been developed by…, Type URH, —ultra rapid hardening, for use where ultra high early strength is desired;, Type VRH, —very rapid hardening, for use where very high early strength is desired;, Type MRH, —medium rapid hardening, for use where mid-range rapid hardening, high early strength is desired; and, Type GRH, —general rapid hardening, for use when the higher strength properties of Type VRH or a Type MRH cement is not required. “ASTM C1600 lists minimum requirements for compressive strength, setting time, shrinkage and soundness (autoclave expansion),” says Hicks. “Optional specifications for sulfate expansion, alkali silicate reactions with aggregates, heat of hydration and expansion in water are also…
-
Test Method Covers Inductively Coupled Plasma Atomic Emission Spectrometry, A new ASTM International standard will help users properly prepare and analyze various nickel-based alloy samples by inductively coupled plasma emission spectrometry. The standard, ASTM E2594 , Test Method for Analysis of Nickel Alloys by Inductively Coupled Plasma Atomic Emission Spectrometry (Performance-Based Method), will assist users in preparing sample and calibration solutions and with…
-
Advancing gas analysis technology is leading to the development of a proposed new ASTM International standard, WK22331 , Test Method for Simultaneous Determination of Oxygen, Nitrogen and Hydrogen in Titanium and Titanium Alloys by the Inert Gas Fusion Technique. Analyzers are now available that can simultaneously test titanium and titanium alloys for oxygen, nitrogen and hydrogen. This…
-
All interested parties are invited to join in the ongoing development of a proposed new standard, WK19982 , Test Method for ICP Analysis of Calcium and Magnesium in Magnesium Ferrosilicon. WK19982 is being developed by Subcommittee E01.01 on Iron, Steel and Ferroalloys, part of ASTM International Committee E01 on Analytical Chemistry for Metals, Ores and Related Materials. According to Robert…