Search
Advanced search
Filter by category
Filter by committee
Search results
-
ASTM International Committee F41 on Unmanned Maritime Vehicle Systems will meet on Aug. 17, 2011, at the Walter E. Washington Convention Center in Washington, D.C. The meeting will take place in conjunction with the AUVSI Unmanned Systems North American 2011 Conference. The F41 executive subcommittee meeting will begin at 7:00 a.m. on Aug. 17. in room 149A. In addition, all interested parties are…
-
A newly approved standard, ASTM D7338 , Guide for the Assessment of Fungal Growth in Buildings, has been developed to provide a go-to reference for anyone testing for mold in buildings. The new standard was developed by Subcommittee D22.08 on Sampling and Analysis of Mold, part of ASTM International Committee D22 on Air Quality. “The lack of consensus standards in the fungal sampling and analysis…, ASTM Committee D22 Next Meeting:, April 10-13, April Committee Week, Anaheim, Calif., Technical Contact:, Lisa Rogers, Mycometer, Inc., Tampa, Fla., Phone: 813-831-6511; lrogers@mycometer.com, ASTM Staff Contact:, David Bradley, Phone: 610-832-9681; dbradley@astm.org, ASTM PR Contact:, Barbara Schindler, Phone: 610-832-9603; bschindl@astm.org Release #8788
-
Air permits from regulatory agencies, such as the U.S. Environmental Protection Agency (USEPA), often require the measurement of a plume's opacity as the plume is emitted from a stationary point source (for example, smokestacks) in the outdoor ambient environment. While such opacity is often visually measured by human observers as “certified smoke readers,” an opacity measurement method using…
-
Rapid hardening hydraulic cements are used in a variety of applications in which reduced cementitious contents are desired or early service is needed. Included among these applications are paving, construction, stucco, mortar and block. A newly approved ASTM International standard covering these cements, ASTM C1600/C1600M , Specification for Rapid Hardening Hydraulic Cement, has been developed by…, Type URH, —ultra rapid hardening, for use where ultra high early strength is desired;, Type VRH, —very rapid hardening, for use where very high early strength is desired;, Type MRH, —medium rapid hardening, for use where mid-range rapid hardening, high early strength is desired; and, Type GRH, —general rapid hardening, for use when the higher strength properties of Type VRH or a Type MRH cement is not required. “ASTM C1600 lists minimum requirements for compressive strength, setting time, shrinkage and soundness (autoclave expansion),” says Hicks. “Optional specifications for sulfate expansion, alkali silicate reactions with aggregates, heat of hydration and expansion in water are also…
-
The measurement of acid mist is becoming increasingly important due to recent actions taken by the U.S. Environmental Protection Agency on fine particles (2.5 micrometers in diameter and smaller) that are unhealthy to breathe. ASTM International Committee D22 on Air Quality is currently working on a proposed standard for measuring acid mists that come from combustion sources, WK22846 , Test…
-
A new ASTM International standard provides guidance for using data generated by ASTM standards in testing for asbestos in surface dust. ASTM D 7390 , Guide for Evaluating Asbestos in Dust on Surfaces by Comparison Between Two Environments, was approved by ASTM International Committee D22 on Air Quality, part of Subcommittee D22.07 on Sampling and Analysis of Asbestos. According to James Millette…
-
A recently approved revision to ASTM International standard C 150 , Specification for Portland Cement, includes three significant technical changes to the document. The changes are part of a joint effort between ASTM and the American Association of State and Highway and Transportation Officials to harmonize C 150 with AASHTO’s standard, M 85, Specification for Portland Cement. C 150 is under the…
-
A new ASTM International standard will provide a method to consistently address indoor air quality complaints in residential buildings and to guide IAQ investigations in an efficient manner. The standard, D 7297 , Practice for Evaluating Residential Indoor Air Quality Concerns, is under the jurisdiction of Subcommittee D22.05 on Indoor Air, part of ASTM International Committee D22 on Air Quality…
-
ASTM International Committee F41 on Unmanned Undersea Vehicle Systems invites all interested parties to participate in a new task group, F41.90.01 on Unmanned Surface Vehicles. With the addition of this new task group, the name of Committee F41 will be changed to Unmanned Maritime Systems. Task Group F41.90.01 is seeking new members with expertise in unmanned surface vehicles to complement the…
-
Laboratories that measure fibers in workplace samples will be the most likely users of two new ASTM International standards: D 7200 , Practice for Sampling and Counting Airborne Fibers, Including Asbestos Fibers, in Mines and Quarries, by Phase Contrast Microscopy and Transmission Electron Microscope; and D 7201 , Practice for Sampling and Counting Airborne Fibers, Including Asbestos Fibers, in…