Search
Advanced search
Filter by category
Filter by committee
Search results
-
A new ASTM International subcommittee has been created to develop standards that will be meaningful and accurate performance indicators to measure work-related injury and illness performance throughout the world. Subcommittee E34.55 on Occupational Safety and Health Performance Improvement is under the jurisdiction of ASTM International Committee E34 on Occupational Health and Safety. “Measuring…
-
ASTM International Committee D15 on Engine Coolants has formed three new subcommittees: Subcommittees D15.22 on Non-Aqueous Coolants ; D15.25 on Diesel Exhaust Fluid ; and D15.30 on Industrial Heat Transfer Fluids . All interested parties are invited to join in the standards developing activities of these new subcommittees., D15.22, Non-Aqueous Coolants, While there has been an increased interest in non-aqueous coolants industry, there are no current ASTM standards in this area. D15.22 will begin to develop such standards. “The envisioned standards for non-aqueous coolants would be performance standards, rather than ingredient standards, to allow for formulations that are not currently proprietary,” says Jonathan T. Light, chief engineer, Evans…, D15.25, Diesel Exhaust Fluid, Diesel exhaust fluid, often referred to as DEF, is required by many diesel engine-powered vehicles delivered after January 2010. More recent environmental standards issued by the U.S. Environmental Protection Agency have created more stringent emissions standards for agricultural, construction and forestry equipment. DEF is used to reduce nitrogen oxide emissions, which allows original equipment…, D15.30, Industrial Heat Transfer Fluids, Members of D15 recognized that changes in the antifreeze industry, including new manufacturing technologies, improved inhibitor chemistries and recycling technologies, would likely be adapted to the facilities industry as a natural course of innovation. Because D15 has experience developing standards that are technically similar to the facilities heat transfer industry, it was deemed appropriate…, ASTM Committee D15 Next Meeting:, May 17-18, May Committee Week, Anaheim, Calif., Technical Contact:, (D15.22) Jonathan T. Light, Evans Cooling Systems Inc., Sharon, Conn., Phone: 860-435-2418; jtlight@comcast.net ; (D15.25) Edward Eaton Sr., Amalgatech, Phoenix, Ariz., Phone: 602-252-0280; edeaton@amalgatech.com ; (D15.30) John Panasewicz, Clear Choice Antifreeze, Henderson, Colo., Phone: 303-227-9900; johnp@clearchoiceantifreeze.com, ASTM Staff Contact:, Joe Koury, Phone: 610-832-9804; jkoury@astm.org, ASTM PR Contact:, Barbara Schindler, Phone: 610-832-9603; bschindl@astm.org Release #8837
-
A series of proposed new standards being developed by ASTM International Committee D15 on Engine Coolants would remove technical barriers that currently prevent the cost-effective replacement of ethylene glycol with more environmentally friendly glycerin in antifreeze. The proposed standards are under the jurisdiction of Subcommittee D15.93 on Research and Long Range Planning. Natural glycerin is…
-
ASTM International Subcommittee E34.50 on Health and Safety Standards for Metalworking Fluids has developed three new standards. Two of the recently approved ASTM standards cover aspects of water-miscible metalworking fluids, while the third concerns prevention of dermatitis in the wet metal removal fluid environment., Prevention of Dermatitis, Dermatitis is an inflammatory response of the skin to a chemical or physical agent. While redness, swelling and itching are typical signs of dermatitis, symptoms can be more severe as well. A new ASTM standard, ASTM E2693 , Practice for Prevention of Dermatitis in the Wet Metal Removal Fluid Environment, discusses dermatitis and its causes and presents a comprehensive approach to dermatitis…, Metalworking Fluids, Two new E34.50 standards address the detection of microbial contamination in metalworking fluids: ASTM E2657 , Test Method for Determination of Endotoxin Concentrations in Water-Miscible Metalworking Fluids, and ASTM E2694 , Test Method for Measurement of Adenosine Triphosphate in Water-Miscible Metalworking Fluids. Both ASTM E2657 and ASTM E2694 measure biological contamination in metalworking…, Participation Invited, The subcommittee is currently looking for participants for an interlaboratory study for ASTM E2657 and ASTM E2694 . “We plan to use a single set of MWF for both standards, so labs who are interested in either or both are welcome to participate,” says Passman. “A few labs will run both the ILS’s for both standards, while most will run one or the other.” Subcommittee E34.50 is part of ASTM…
-
Rapid hardening hydraulic cements are used in a variety of applications in which reduced cementitious contents are desired or early service is needed. Included among these applications are paving, construction, stucco, mortar and block. A newly approved ASTM International standard covering these cements, ASTM C1600/C1600M , Specification for Rapid Hardening Hydraulic Cement, has been developed by…, Type URH, —ultra rapid hardening, for use where ultra high early strength is desired;, Type VRH, —very rapid hardening, for use where very high early strength is desired;, Type MRH, —medium rapid hardening, for use where mid-range rapid hardening, high early strength is desired; and, Type GRH, —general rapid hardening, for use when the higher strength properties of Type VRH or a Type MRH cement is not required. “ASTM C1600 lists minimum requirements for compressive strength, setting time, shrinkage and soundness (autoclave expansion),” says Hicks. “Optional specifications for sulfate expansion, alkali silicate reactions with aggregates, heat of hydration and expansion in water are also…
-
All interested parties in the glass industry are invited to participate in the development of a proposed new standard guide for the safe handling of annealed glass. The new standard will be developed by a task group within ASTM Committee E34 on Occupational Health and Safety. A small group from industry and OSHA met in Rossford, Ohio, in March to discuss this new activity. The task group plans to…
-
A recently approved revision to ASTM International standard C 150 , Specification for Portland Cement, includes three significant technical changes to the document. The changes are part of a joint effort between ASTM and the American Association of State and Highway and Transportation Officials to harmonize C 150 with AASHTO’s standard, M 85, Specification for Portland Cement. C 150 is under the…
-
Information and product destruction services is a rapidly growing industry. In order to develop standards to serve the needs of this industry, ASTM International Committee E34 on Occupational Health and Safety has formed Subcommittee E34.25 on Mobile and Plant-Based Security Destruction Equipment Safety Requirements. All interested parties are invited to participate in the standards developing…
-
In response to changing emissions restrictions and consumer expectations, ASTM International Committee D15 on Engine Coolants is now developing a proposed new standard, WK16003 , Specification for Engine Coolant Grade 1,3-propanediol (PDO). This task group is under the jurisdiction of Subcommittee D15.07 on Specifications. Edward Eaton, D15 member and chief engineer, Amalgatech, says that as…
-
An important standard that is used to help protect the health of workers where there may be occupational exposure to quartz dust has recently been revised. ASTM standard E 1132 , Practice for Health Requirements Relating to Occupational Exposure to Respirable Crystalline Silica, was developed by Subcommittee E34.16 on Silicas, which is under the jurisdiction of Committee E34 on Occupational…