Search
Advanced search
Filter by category
Filter by committee
Search results
-
Fatigue fretting is the process of crack formation and progressive crack growth at a location in a mechanical system where two components are in contact and undergoing a vibratory loading. A new ASTM International standard provides insight on what conditions promote fretting fatigue and offers approaches to design an experiment to assess it. ASTM E2789 , Guide for Fretting Fatigue Testing, was…, ASTM Committee E08 Next Meeting:, May 16-20, May Committee Week, Anaheim, Calif., Technical Contact:, Richard W. Neu, Georgia Institute of Technology, Atlanta, Ga., Phone: 404-894-3074; rick.neu@gatech.edu ASTM Staff Contact: Jeff Adkins, Phone: 610-832-9738; jadkins@astm.org ASTM PR Contact: Barbara Schindler, Phone: 610-832-9603; bschindl@astm.org R elease #8809
-
Creep-fatigue testing simulates the loading and temperature conditions experienced by turbine components of aircraft engines, nuclear reactor components and fossil power plant components during service. With increasing need for cyclic operation during peak power demands, reliable creep-fatigue test data is necessary for the life assessment of aging power plants. A new ASTM standard, ASTM E2714 ,…
-
A proposed new ASTM standard will assist in establishing tests for fretting fatigue, an issue at attachments and joints in a variety of mechanical, aeronautical and biomedical engineering systems and devices. WK24298 , Guide for Fretting Fatigue Testing, is being developed by Subcommittee E08.05 on Cyclic Deformation and Fatigue Crack Formation, part of ASTM International Committee E08 on Fatigue…, ASTM Committee E08 Next Meeting:, May 17-20, 2010, May Committee Week, St. Louis, Mo., Technical Contact:, Richard W. Neu, Georgia Institute of Technology, Atlanta, Ga., Phone: 404-894-3074; rick.neu@gatech.edu, ASTM Staff Contact:, Jeff Adkins, Phone: 610-832-9738; jadkins@astm.org, ASTM PR Contact:, Barbara Schindler, Phone: 610-832-9603; bschindl@astm.org Release #8430/Dec2009
-
Rapid hardening hydraulic cements are used in a variety of applications in which reduced cementitious contents are desired or early service is needed. Included among these applications are paving, construction, stucco, mortar and block. A newly approved ASTM International standard covering these cements, ASTM C1600/C1600M , Specification for Rapid Hardening Hydraulic Cement, has been developed by…, Type URH, —ultra rapid hardening, for use where ultra high early strength is desired;, Type VRH, —very rapid hardening, for use where very high early strength is desired;, Type MRH, —medium rapid hardening, for use where mid-range rapid hardening, high early strength is desired; and, Type GRH, —general rapid hardening, for use when the higher strength properties of Type VRH or a Type MRH cement is not required. “ASTM C1600 lists minimum requirements for compressive strength, setting time, shrinkage and soundness (autoclave expansion),” says Hicks. “Optional specifications for sulfate expansion, alkali silicate reactions with aggregates, heat of hydration and expansion in water are also…
-
Data produced from the use of a proposed new ASTM International standard will be employed in the design of new, more efficient aircraft engines as well as for piping, steam and gas turbines used in power generation. The proposed new standard, WK21984 , Test Method for Creep-Fatigue Crack Growth Rate Testing, is being developed by Subcommittee E08.06 on Crack Growth Behavior, part of ASTM…
-
The use of rolling devices can provide a means to evaluate the adhesion of weather seals, for quality control in new installations, general evaluation of existing installations, and the investigation of water and air leakage through building enclosures. In order to better facilitate the use of rolling devices, ASTM International Committee C24 on Building Seals and Sealants is developing a…
-
A recently approved revision to ASTM International standard C 150 , Specification for Portland Cement, includes three significant technical changes to the document. The changes are part of a joint effort between ASTM and the American Association of State and Highway and Transportation Officials to harmonize C 150 with AASHTO’s standard, M 85, Specification for Portland Cement. C 150 is under the…
-
ASTM International Committee C24 on Building Seals and Sealants invites interested parties to participate in the development of a proposed new standard that will use photographs to illustrate various types of sealant failures. WK11731 , Guide for Diagnosing Sealant Failure by Comparison to Reference Photographs, is under the jurisdiction of Subcommittee C24.10 on Specifications, Guides and…
-
Verifying the results of application software used to calculate the mechanical properties of materials is the subject of a new standard developed by ASTM International Committee E08 on Fatigue and Fracture. The new standard, E 2443, Guide for Verifying Computer-Generated Test Results Through the Use of Standard Data Sets, is under the jurisdiction of Subcommittee E08.03 on Advanced Apparatus and…
-
Many structures, such as aircraft or other lightweight vehicles, are made from thin-ductile structural materials that exhibit low crack-front constraint, which allows for extensive plastic yielding of the material around a crack front. However, many current standards, such as E 399, Test Method for Linear-Elastic Plane-Strain Fracture Toughness K Ic of Metallic Materials, or E 1820, Test Method…