Search
Advanced search
Filter by category
Filter by committee
Search results
-
Piston ring/liner interface can contribute as much as half the total friction loss in internal combustion engines, with the resulting wear leading to reduced energy efficiency and raised emissions. A new ASTM International standard provides a method to more accurately measure small amounts of wear on curved piston ring segments and their counterfaces after lubricated bench-scale testing. “Coupled…
-
ASTM Committee G02 on Wear and Erosion is including a field trip in the plans for its Dec. 8-9 meeting in Jacksonville, Fla. Committee members will be visiting the Tribology Laboratory in the mechanical engineering department at the University of Florida in Gainesville. The Tribology Laboratory is actively involved in a wide variety of tribological research and tribology education projects. The…
-
Several years ago, a housing boom followed by recovery from damage caused by Hurricane Katrina and other storms created a surge in the use of imported drywall in the United States, particularly in the southeastern area of the country. However, since then, there have been a number of complaints concerning corrosion and odors in homes in which some of this drywall was used. Interim guidance…
-
A new ASTM standard will be useful to slide and engine companies, as well as makers of bushing materials, in studies that involve the measurement of system friction forces. The new standard, ASTM G203 , Guide for Determining Friction Energy Dissipation in Reciprocating Tribosystems, was developed by Subcommittee G02.50 on Friction, part of ASTM International Committee G02 on Wear and Erosion.…
-
With heightened interest in issues involving corrosive gypsum board, the first draft of a proposed new standard on the subject, ASTM WK26072 , Practice for Evaluation of Buildings to Identify Corrosive Gypsum Board, was reviewed and edited at a task group meeting on Nov. 10 in Atlanta, Ga. The proposed new standard is under the jurisdiction of ASTM Subcommittee C11.01 on Specifications and Test…, ASTM Committee C11 Next Meeting:, May 17-19, 2010, St. Louis, Mo., Technical Contact:, Spiderman Mulholland, U.S. Building Consultants Inc., Gainesville, Fla., Phone: 352-505-6771; spiderman@usbcinc.com, ASTM Staff Contact:, Thomas O’Toole, Phone: 610-832-9739; totoole@astm.org, ASTM PR Contact:, Barbara Schindler, Phone: 610-832-9603; bschindl@astm.org Release #8414/Nov2009
-
At an ASTM International meeting held on Oct. 20 it was decided to initiate the formulation of a proposed new ASTM standard that will cover issues relating to drywall and indoor air quality. Representatives from various ASTM International committees, including C11 on Gypsum and Related Building Materials and Systems and E06 on Performance of Buildings attended the meeting, which was held during…
-
Rapid hardening hydraulic cements are used in a variety of applications in which reduced cementitious contents are desired or early service is needed. Included among these applications are paving, construction, stucco, mortar and block. A newly approved ASTM International standard covering these cements, ASTM C1600/C1600M , Specification for Rapid Hardening Hydraulic Cement, has been developed by…, Type URH, —ultra rapid hardening, for use where ultra high early strength is desired;, Type VRH, —very rapid hardening, for use where very high early strength is desired;, Type MRH, —medium rapid hardening, for use where mid-range rapid hardening, high early strength is desired; and, Type GRH, —general rapid hardening, for use when the higher strength properties of Type VRH or a Type MRH cement is not required. “ASTM C1600 lists minimum requirements for compressive strength, setting time, shrinkage and soundness (autoclave expansion),” says Hicks. “Optional specifications for sulfate expansion, alkali silicate reactions with aggregates, heat of hydration and expansion in water are also…
-
The use of non-metallic plaster bases (lath) is growing in the construction industry, and minimum consensus standards are being set for installation, test methods and performance requirements. A task group within Subcommittee C11.02 on Specifications and Test Methods for Accessories and Related Products is currently developing three lath standards: ASTM WK24554 , Test Method for Non-Metallic…
-
ASTM International Committee E29 on Particle and Spray Characterization has recently approved an extensive revision of ASTM standard E11 , Specification for Wire Cloth and Sieves for Testing Purposes. The revision will lead to better control of the quality of sieve cloths and test sieves. ASTM E11 is under the jurisdiction of Subcommittee E29.01 on Sieves, Sieving Methods and Screening Media.…
-
A recently approved revision to ASTM International standard C 150 , Specification for Portland Cement, includes three significant technical changes to the document. The changes are part of a joint effort between ASTM and the American Association of State and Highway and Transportation Officials to harmonize C 150 with AASHTO’s standard, M 85, Specification for Portland Cement. C 150 is under the…