Search
Advanced search
Filter by category
Filter by committee
Search results
-
Several years ago, a housing boom followed by recovery from damage caused by Hurricane Katrina and other storms created a surge in the use of imported drywall in the United States, particularly in the southeastern area of the country. However, since then, there have been a number of complaints concerning corrosion and odors in homes in which some of this drywall was used. Interim guidance…
-
Since the appearance of the first California-type models around 1940, the profilograph has been a popular device used for quality control in the construction of pavements. Both roadway and airfield landing agencies have adopted roughness indexes computed from profilograph-derived measurements as a level of construction quality. Emerging high-speed inertial profilers can now quickly collect…
-
With heightened interest in issues involving corrosive gypsum board, the first draft of a proposed new standard on the subject, ASTM WK26072 , Practice for Evaluation of Buildings to Identify Corrosive Gypsum Board, was reviewed and edited at a task group meeting on Nov. 10 in Atlanta, Ga. The proposed new standard is under the jurisdiction of ASTM Subcommittee C11.01 on Specifications and Test…, ASTM Committee C11 Next Meeting:, May 17-19, 2010, St. Louis, Mo., Technical Contact:, Spiderman Mulholland, U.S. Building Consultants Inc., Gainesville, Fla., Phone: 352-505-6771; spiderman@usbcinc.com, ASTM Staff Contact:, Thomas O’Toole, Phone: 610-832-9739; totoole@astm.org, ASTM PR Contact:, Barbara Schindler, Phone: 610-832-9603; bschindl@astm.org Release #8414/Nov2009
-
At an ASTM International meeting held on Oct. 20 it was decided to initiate the formulation of a proposed new ASTM standard that will cover issues relating to drywall and indoor air quality. Representatives from various ASTM International committees, including C11 on Gypsum and Related Building Materials and Systems and E06 on Performance of Buildings attended the meeting, which was held during…
-
A proposed new standard being developed by ASTM International Committee E17 on Vehicle-Pavement Systems will be the first to describe how truth-in-data should be applied to traffic monitoring data collection, summarization and reporting. WK25280 , Practice for Highway Traffic Monitoring Truth-in-Data, is under the jurisdiction of Subcommittee E17.52 on Traffic Monitoring. Current traffic…
-
Rapid hardening hydraulic cements are used in a variety of applications in which reduced cementitious contents are desired or early service is needed. Included among these applications are paving, construction, stucco, mortar and block. A newly approved ASTM International standard covering these cements, ASTM C1600/C1600M , Specification for Rapid Hardening Hydraulic Cement, has been developed by…, Type URH, —ultra rapid hardening, for use where ultra high early strength is desired;, Type VRH, —very rapid hardening, for use where very high early strength is desired;, Type MRH, —medium rapid hardening, for use where mid-range rapid hardening, high early strength is desired; and, Type GRH, —general rapid hardening, for use when the higher strength properties of Type VRH or a Type MRH cement is not required. “ASTM C1600 lists minimum requirements for compressive strength, setting time, shrinkage and soundness (autoclave expansion),” says Hicks. “Optional specifications for sulfate expansion, alkali silicate reactions with aggregates, heat of hydration and expansion in water are also…
-
The use of non-metallic plaster bases (lath) is growing in the construction industry, and minimum consensus standards are being set for installation, test methods and performance requirements. A task group within Subcommittee C11.02 on Specifications and Test Methods for Accessories and Related Products is currently developing three lath standards: ASTM WK24554 , Test Method for Non-Metallic…
-
Being able to compile and interpret data on how traffic turns through an intersection could have an impact on future environmental and safety decisions regarding intersection geometry and traffic control. However, until recently no standard has existed to properly obtain and use this data. Now, ASTM International Committee E17 on Vehicle-Pavement Systems has approved E2667 , Practice for…
-
A recently approved revision to ASTM International standard C 150 , Specification for Portland Cement, includes three significant technical changes to the document. The changes are part of a joint effort between ASTM and the American Association of State and Highway and Transportation Officials to harmonize C 150 with AASHTO’s standard, M 85, Specification for Portland Cement. C 150 is under the…
-
Drawing on the best practices of the U.S. Federal Highway Administration and the states, ASTM International Committee E17 on Vehicle-Pavement Systems has developed a new standard, E 2561 , Practice for Installation of Inductive Loop Detectors. E 2561 is under the jurisdiction of Subcommittee E17.52 on Traffic Monitoring. Inductive loop detectors are installed in sawed slots in roadway pavement…