Search
Advanced search
Filter by category
Filter by committee
Search results
-
New regulations set forth by the U.S. Environmental Protection Agency to mandate greenhouse gas reporting in the U.S. carbon black industry have led to the development of a new ASTM International standard, ASTM D7662 , Test Method for Carbon Content in Carbon Black Feedstock Oils. ASTM D7662 is under the jurisdiction of Subcommittee D24.66 on Environment, Health and Safety, part of ASTM…
-
The U.S. Environmental Protection Agency has set forth new regulations that mandate greenhouse gas reporting in the U.S. carbon black industry. These regulations were the impetus for the development of a new ASTM International standard, ASTM D7633 , Test Method for Carbon Black Carbon Content. The new standard was developed by Subcommittee D24.66 on Environment, Health and Safety, part of ASTM…, ASTM Committee D24 Next Meeting:, Dec. 6-8, December Committee Week, New Orleans, La., Technical Contact:, George Joyce, Columbian Chemicals Co., Marietta, Ga., Phone: 770-792-9467; gjoyce@columbianchemicals.com, ASTM Staff Contact:, Joe Koury, Phone: 610-832-9804; jkoury@astm.org, ASTM PR Contact:, Barbara Schindler, Phone: 610-832-9603; bschindl@astm.org Release #8641
-
An increased interest in the polyaromatic hydrocarbon content of carbon black, particularly in Europe, and new U.S. Environmental Protection Agency requirements to report greenhouse gas emissions from U.S. industry including carbon black plants has led to the formation of a new ASTM subcommittee. Subcommittee D24.66 on Environment, Health and Safety is part of ASTM International Committee D24 on…
-
Flow characteristics of fine metal powders are important in filling dies for pressing of powder metallurgy compacts, which are later sintered and sometimes machined into finished parts. The flow rate, as measured by a new ASTM standard, determines the flow necessary for a precise quantity of powder to be introduced into the die. The new standard, B964 , Test Methods for Flow Rate of Metal Powders…
-
Two recently approved ASTM International standards provide user-friendly tests for properties of sintered metallurgy products. The new standards, developed by Subcommittee B09.04 on Bearings, are ASTM B962 , Test Methods for Density of Compacted or Sintered Power Metallurgy (PM) Products Using Archimedes’ Principle, and ASTM B963 , Test Methods for Oil Content, Oil-Impregnation Efficiency and…
-
No industry standard currently exists that addresses the vacuum sealing requirements of knife-edged flanges for high vacuum applications. Existing international standards focus on interchangeability of the hardware, but do not address the reliability of the seal. ASTM International Committee E42 on Surface Analysis is now working on a proposed standard on the subject, WK21206 , Specification…
-
A 2002 workshop on galling wear held by ASTM International Committee G02 on Wear and Erosion provided the impetus for the development of a new standard, ASTM G196 , Test Method for Galling Resistance of Material Couples. The new standard is under the jurisdiction of Subcommittee G02.40 on Non-Abrasive Wear. According to Scott Hummel, Ph.D., associate professor, head of the department of…
-
A proposed new standard being developed by ASTM International Committee B09 on Metal Powders and Metal Powder Products offers a solution to the challenge of handling and characterizing very fine powders. Subcommittee B09.02 on Base Metal Powders is developing the proposed standard, WK13023 , Test Method for Determination of Tap Density of Metallic Powders by a Constant Volume Measuring Method. …
-
Conventionally processed powder metallurgy materials often exhibit open microporosity at the surface. While it is a natural part of the process, this microporosity can affect the measurement of surface finishes. To cover this and other issues that arise from measuring the surface finish of powder metallurgy, ASTM International Committee B09 on Metal Powders and Metal Powder Products has developed…
-
ASTM International Committee E42 on Surface Analysis has approved a new standard, E 2382, Guide to Scanner and Tip Related Artifacts in Scanning Tunneling Microscopy and Atomic Force Microscopy. The guide, under the jurisdiction of Subcommittee E42.14 on STM/AFM, was proposed in order to assist new scanning probe microscopy users with more rapid recognition and assessment of artifacts in imaging…