Search
Advanced search
Filter by category
Filter by committee
Search results
-
As a means of ensuring the safety of electrical wiring systems in airplanes, ASTM International Committee F39 on Normal and Utility Category Airplane Electrical Wiring Systems has recently approved F2639 , Practice for Design, Alteration and Certification of Airplane Electrical Wiring Systems, a standard developed by Subcommittee F39.01 on Design, Alteration and Certification. According to…
-
Users of laboratory services and other interested parties are invited to participate in the development of a new practice that will promote uniformity in quality management practice for all standards under the jurisdiction of ASTM International Committee D05 on Coal and Coke. Subcommittee D05.30 on Quality Assurance is developing the proposed new standard, WK14563 , Establishing the Competence of…
-
A proposed new standard being developed by ASTM International Committee B09 on Metal Powders and Metal Powder Products offers a solution to the challenge of handling and characterizing very fine powders. Subcommittee B09.02 on Base Metal Powders is developing the proposed standard, WK13023 , Test Method for Determination of Tap Density of Metallic Powders by a Constant Volume Measuring Method. …
-
Sampling is a difficult but essential part of the coal production process. ASTM International Committee D05 on Coal and Coke hopes to streamline that process with the publication of new standard D 7256/D 7256M, Practice for Mechanical Collection and Within-System Preparation of a Gross Sample of Coal from Moving Streams. Practice D 7256/D 7256M is under the jurisdiction of Subcommittee D05.23 on…
-
A new ASTM International standard, F 2490 , Guide for Aircraft Electrical Load and Power Source Capacity Analysis, has been accepted by the Federal Aviation Administration (FAA) as a means of compliance with 14 CFR 23.1351(a) (2), Electrical System Capacity for Part 23 (and Predecessor) Aircraft. Guide F 2490 was developed by Subcommittee F39.01 on Design, Alteration, and Certification, which is…
-
Conventionally processed powder metallurgy materials often exhibit open microporosity at the surface. While it is a natural part of the process, this microporosity can affect the measurement of surface finishes. To cover this and other issues that arise from measuring the surface finish of powder metallurgy, ASTM International Committee B09 on Metal Powders and Metal Powder Products has developed…
-
ASTM International Committee F16 on Fasteners has recently approved an important new standard that deals with coated threaded fasteners and washers by hot-dip zinc galvanizing. The standard, F 2329, Specification for Zinc Coating, Hot-Dip, Requirements for Application to Carbon and Alloy Steel Bolts, Screws, Washers, Nuts and Special Threaded Fasteners, is under the jurisdiction of Subcommittee…
-
ASTM International Committee D05 on Coal and Coke is currently seeking participation in the development of a proposed new standard, WK10700 , Test Method for Total Moisture in Coal Reduced to 2.36 mm (No. 8 Sieve) Topsize Through Determination of Air-Drying Loss by Microwave Oven. The proposed new standard is under the jurisdiction of Subcommittee D05.21 on Methods of Analysis. While air-drying…
-
ASTM Committee D05 on Coal and Coke is currently developing a proposed new standard, WK10380, Practice for Establishing the Competence of Laboratories Using ASTM Procedures in the Sampling and Analysis of Coal and Coke. The proposed standard will specify requirements for establishing, operating and evaluating a laboratory that provides services in the areas of sample collection and preparation…
-
Most of the coal burned in the United States contains only trace amounts of chloride and fluoride. However, due to the increasing regulation of these compounds for clean air initiatives, being able to measure even small amounts of chloride and fluoride in coal has taken on a greater importance than ever. Recognizing this, ASTM International Committee D05 on Coal and Coke has begun to develop a…