Search
Advanced search
Filter by category
Filter by committee
Search results
-
With heightened interest in issues involving corrosive gypsum board, the first draft of a proposed new standard on the subject, ASTM WK26072 , Practice for Evaluation of Buildings to Identify Corrosive Gypsum Board, was reviewed and edited at a task group meeting on Nov. 10 in Atlanta, Ga. The proposed new standard is under the jurisdiction of ASTM Subcommittee C11.01 on Specifications and Test…, ASTM Committee C11 Next Meeting:, May 17-19, 2010, St. Louis, Mo., Technical Contact:, Spiderman Mulholland, U.S. Building Consultants Inc., Gainesville, Fla., Phone: 352-505-6771; spiderman@usbcinc.com, ASTM Staff Contact:, Thomas O’Toole, Phone: 610-832-9739; totoole@astm.org, ASTM PR Contact:, Barbara Schindler, Phone: 610-832-9603; bschindl@astm.org Release #8414/Nov2009
-
At an ASTM International meeting held on Oct. 20 it was decided to initiate the formulation of a proposed new ASTM standard that will cover issues relating to drywall and indoor air quality. Representatives from various ASTM International committees, including C11 on Gypsum and Related Building Materials and Systems and E06 on Performance of Buildings attended the meeting, which was held during…
-
Rapid hardening hydraulic cements are used in a variety of applications in which reduced cementitious contents are desired or early service is needed. Included among these applications are paving, construction, stucco, mortar and block. A newly approved ASTM International standard covering these cements, ASTM C1600/C1600M , Specification for Rapid Hardening Hydraulic Cement, has been developed by…, Type URH, —ultra rapid hardening, for use where ultra high early strength is desired;, Type VRH, —very rapid hardening, for use where very high early strength is desired;, Type MRH, —medium rapid hardening, for use where mid-range rapid hardening, high early strength is desired; and, Type GRH, —general rapid hardening, for use when the higher strength properties of Type VRH or a Type MRH cement is not required. “ASTM C1600 lists minimum requirements for compressive strength, setting time, shrinkage and soundness (autoclave expansion),” says Hicks. “Optional specifications for sulfate expansion, alkali silicate reactions with aggregates, heat of hydration and expansion in water are also…
-
Flow characteristics of fine metal powders are important in filling dies for pressing of powder metallurgy compacts, which are later sintered and sometimes machined into finished parts. The flow rate, as measured by a new ASTM standard, determines the flow necessary for a precise quantity of powder to be introduced into the die. The new standard, B964 , Test Methods for Flow Rate of Metal Powders…
-
The use of non-metallic plaster bases (lath) is growing in the construction industry, and minimum consensus standards are being set for installation, test methods and performance requirements. A task group within Subcommittee C11.02 on Specifications and Test Methods for Accessories and Related Products is currently developing three lath standards: ASTM WK24554 , Test Method for Non-Metallic…
-
Two recently approved ASTM International standards provide user-friendly tests for properties of sintered metallurgy products. The new standards, developed by Subcommittee B09.04 on Bearings, are ASTM B962 , Test Methods for Density of Compacted or Sintered Power Metallurgy (PM) Products Using Archimedes’ Principle, and ASTM B963 , Test Methods for Oil Content, Oil-Impregnation Efficiency and…
-
A recently approved revision to ASTM International standard C 150 , Specification for Portland Cement, includes three significant technical changes to the document. The changes are part of a joint effort between ASTM and the American Association of State and Highway and Transportation Officials to harmonize C 150 with AASHTO’s standard, M 85, Specification for Portland Cement. C 150 is under the…
-
The market growth and wide acceptance of glass mat gypsum panels has led to the development and approval of a new ASTM International standard. C 1658/C 1658M , Specification for Glass Mat Gypsum Panels, is under the jurisdiction of Subcommittee C11.01 on Specifications and Test Methods for Gypsum Products, which is part of ASTM International Committee C11 on Gypsum and Related Building Materials…
-
A proposed new standard being developed by ASTM International Committee B09 on Metal Powders and Metal Powder Products offers a solution to the challenge of handling and characterizing very fine powders. Subcommittee B09.02 on Base Metal Powders is developing the proposed standard, WK13023 , Test Method for Determination of Tap Density of Metallic Powders by a Constant Volume Measuring Method. …
-
Conventionally processed powder metallurgy materials often exhibit open microporosity at the surface. While it is a natural part of the process, this microporosity can affect the measurement of surface finishes. To cover this and other issues that arise from measuring the surface finish of powder metallurgy, ASTM International Committee B09 on Metal Powders and Metal Powder Products has developed…