Search
Advanced search
Filter by category
Filter by committee
Search results
-
Consumers who are purchasing building materials for homes want to be assured that the materials are mold resistant. A proposed new ASTM standard will allow for a mold-resistance rating to be given to specific materials, depending on how the materials perform to the test method. The proposed new standard, ASTM WK32079 , Test Method for Determination of Mold Growth on Building Products Designed for…
-
While standards for outdoor calibration techniques for solar radiometers exist, there are currently no general standards that deal with issues of indoor calibration transfers between radiometers of different design. A proposed new ASTM standard, ASTM WK27263, Test Method for Indoor Transfer of Calibration from Reference to Field Pyranometers, will address in detail issues associated with…
-
Rapid hardening hydraulic cements are used in a variety of applications in which reduced cementitious contents are desired or early service is needed. Included among these applications are paving, construction, stucco, mortar and block. A newly approved ASTM International standard covering these cements, ASTM C1600/C1600M , Specification for Rapid Hardening Hydraulic Cement, has been developed by…, Type URH, —ultra rapid hardening, for use where ultra high early strength is desired;, Type VRH, —very rapid hardening, for use where very high early strength is desired;, Type MRH, —medium rapid hardening, for use where mid-range rapid hardening, high early strength is desired; and, Type GRH, —general rapid hardening, for use when the higher strength properties of Type VRH or a Type MRH cement is not required. “ASTM C1600 lists minimum requirements for compressive strength, setting time, shrinkage and soundness (autoclave expansion),” says Hicks. “Optional specifications for sulfate expansion, alkali silicate reactions with aggregates, heat of hydration and expansion in water are also…
-
Flow characteristics of fine metal powders are important in filling dies for pressing of powder metallurgy compacts, which are later sintered and sometimes machined into finished parts. The flow rate, as measured by a new ASTM standard, determines the flow necessary for a precise quantity of powder to be introduced into the die. The new standard, B964 , Test Methods for Flow Rate of Metal Powders…
-
Two recently approved ASTM International standards provide user-friendly tests for properties of sintered metallurgy products. The new standards, developed by Subcommittee B09.04 on Bearings, are ASTM B962 , Test Methods for Density of Compacted or Sintered Power Metallurgy (PM) Products Using Archimedes’ Principle, and ASTM B963 , Test Methods for Oil Content, Oil-Impregnation Efficiency and…
-
Explorations into alternative forms of energy have increased interest in standards for solar energy applications. ASTM International Committee G03 on Weathering and Durability has recently approved a new standard in this area, G197 , Table for Reference Solar Spectral Distributions: Direct and Diffuse on 20° Tilted and Vertical Surfaces. ASTM G197 was developed by Subcommittee G03.09 on…
-
Automotive companies and interior suppliers will be the primary users of a proposed new ASTM International standard that will aid in testing of automotive interior materials and parts, draperies or other applications in which durability behind glass is desired. The proposed standard, WK16895 , Practice for Conducting Exposures in Outdoor Glass-Covered Exposure Apparatus with Air Recirculation, is…
-
A recently approved revision to ASTM International standard C 150 , Specification for Portland Cement, includes three significant technical changes to the document. The changes are part of a joint effort between ASTM and the American Association of State and Highway and Transportation Officials to harmonize C 150 with AASHTO’s standard, M 85, Specification for Portland Cement. C 150 is under the…
-
A proposed new standard being developed by ASTM International Committee B09 on Metal Powders and Metal Powder Products offers a solution to the challenge of handling and characterizing very fine powders. Subcommittee B09.02 on Base Metal Powders is developing the proposed standard, WK13023 , Test Method for Determination of Tap Density of Metallic Powders by a Constant Volume Measuring Method. …
-
Conventionally processed powder metallurgy materials often exhibit open microporosity at the surface. While it is a natural part of the process, this microporosity can affect the measurement of surface finishes. To cover this and other issues that arise from measuring the surface finish of powder metallurgy, ASTM International Committee B09 on Metal Powders and Metal Powder Products has developed…