Search
Advanced search
Filter by category
Filter by committee
Search results
-
The purpose of a laboratory roadwheel test is to realistically evaluate tires for specific road conditions. To facilitate such tests, ASTM International Committee F09 on Tires has developed a practice to provide an industry standard for commercial radial truck-bus tire laboratory temperature algorithms. The algorithms equilibrate with flat surface (highway) operating temperatures to determine…
-
A rim slip performance test for tires that has been done at the Nevada Automotive Test Center for more than 20 years has now become an ASTM International standard. ASTM F2803 , Test Method for Evaluating Rim Slip Performance of Tires and Wheels, was developed by Subcommittee F09.20 on Vehicular Testing, part of ASTM International Committee F09 on Tires. Rim slip occurs when tire and wheel…, ASTM Committee F09 Next Meeting:, April 21-22, April committee week, St. Louis, Mo., Technical Contact:, Jason Whiteley, Nevada Automotive Test Center, Silver Springs, Nev., Phone: 775-629-2000, jwhiteley@natc-ht.com, ASTM Staff Contact:, Rick Lake, Phone: 610-832-9689; rlake@astm.org, ASTM PR Contact:, Barbara Schindler, Phone: 610-832-9603; bschindl@astm.org Release #8494/Feb2010
-
Rapid hardening hydraulic cements are used in a variety of applications in which reduced cementitious contents are desired or early service is needed. Included among these applications are paving, construction, stucco, mortar and block. A newly approved ASTM International standard covering these cements, ASTM C1600/C1600M , Specification for Rapid Hardening Hydraulic Cement, has been developed by…, Type URH, —ultra rapid hardening, for use where ultra high early strength is desired;, Type VRH, —very rapid hardening, for use where very high early strength is desired;, Type MRH, —medium rapid hardening, for use where mid-range rapid hardening, high early strength is desired; and, Type GRH, —general rapid hardening, for use when the higher strength properties of Type VRH or a Type MRH cement is not required. “ASTM C1600 lists minimum requirements for compressive strength, setting time, shrinkage and soundness (autoclave expansion),” says Hicks. “Optional specifications for sulfate expansion, alkali silicate reactions with aggregates, heat of hydration and expansion in water are also…
-
Flow characteristics of fine metal powders are important in filling dies for pressing of powder metallurgy compacts, which are later sintered and sometimes machined into finished parts. The flow rate, as measured by a new ASTM standard, determines the flow necessary for a precise quantity of powder to be introduced into the die. The new standard, B964 , Test Methods for Flow Rate of Metal Powders…
-
Two recently approved ASTM International standards provide user-friendly tests for properties of sintered metallurgy products. The new standards, developed by Subcommittee B09.04 on Bearings, are ASTM B962 , Test Methods for Density of Compacted or Sintered Power Metallurgy (PM) Products Using Archimedes’ Principle, and ASTM B963 , Test Methods for Oil Content, Oil-Impregnation Efficiency and…
-
A recently approved revision to ASTM International standard C 150 , Specification for Portland Cement, includes three significant technical changes to the document. The changes are part of a joint effort between ASTM and the American Association of State and Highway and Transportation Officials to harmonize C 150 with AASHTO’s standard, M 85, Specification for Portland Cement. C 150 is under the…
-
Measuring the performance of a new standard reference test tire (SRTT) in a variety of situations is the purpose of a new ASTM International standard, F 2493 , Specification for P225/60R16 97S Radial Standard Reference Test Tire. The standard, which was developed by Subcommittee F09.20 on Vehicular Testing, is under the jurisdiction of ASTM International Committee F09 on Tires. F 2493 is a…
-
A proposed new standard being developed by ASTM International Committee B09 on Metal Powders and Metal Powder Products offers a solution to the challenge of handling and characterizing very fine powders. Subcommittee B09.02 on Base Metal Powders is developing the proposed standard, WK13023 , Test Method for Determination of Tap Density of Metallic Powders by a Constant Volume Measuring Method. …
-
Conventionally processed powder metallurgy materials often exhibit open microporosity at the surface. While it is a natural part of the process, this microporosity can affect the measurement of surface finishes. To cover this and other issues that arise from measuring the surface finish of powder metallurgy, ASTM International Committee B09 on Metal Powders and Metal Powder Products has developed…
-
After a 35-year-absence, the natural cement industry is being revived and, along with it, a long-withdrawn ASTM International standard. Until it closed in 1970, the Century Cement Company in Rosendale, N.Y. was the last company to manufacture natural cement. Up to that point, Rosendale had been the center of the industry, the source of more than half of all natural cement produced in the U.S.…