Search
Advanced search
Filter by category
Filter by committee
Search results
-
The U.S. Environmental Protection Agency has set forth new regulations that mandate greenhouse gas reporting in the U.S. carbon black industry. These regulations were the impetus for the development of a new ASTM International standard, ASTM D7633 , Test Method for Carbon Black Carbon Content. The new standard was developed by Subcommittee D24.66 on Environment, Health and Safety, part of ASTM…, ASTM Committee D24 Next Meeting:, Dec. 6-8, December Committee Week, New Orleans, La., Technical Contact:, George Joyce, Columbian Chemicals Co., Marietta, Ga., Phone: 770-792-9467; gjoyce@columbianchemicals.com, ASTM Staff Contact:, Joe Koury, Phone: 610-832-9804; jkoury@astm.org, ASTM PR Contact:, Barbara Schindler, Phone: 610-832-9603; bschindl@astm.org Release #8641
-
An increased interest in the polyaromatic hydrocarbon content of carbon black, particularly in Europe, and new U.S. Environmental Protection Agency requirements to report greenhouse gas emissions from U.S. industry including carbon black plants has led to the formation of a new ASTM subcommittee. Subcommittee D24.66 on Environment, Health and Safety is part of ASTM International Committee D24 on…
-
Rapid hardening hydraulic cements are used in a variety of applications in which reduced cementitious contents are desired or early service is needed. Included among these applications are paving, construction, stucco, mortar and block. A newly approved ASTM International standard covering these cements, ASTM C1600/C1600M , Specification for Rapid Hardening Hydraulic Cement, has been developed by…, Type URH, —ultra rapid hardening, for use where ultra high early strength is desired;, Type VRH, —very rapid hardening, for use where very high early strength is desired;, Type MRH, —medium rapid hardening, for use where mid-range rapid hardening, high early strength is desired; and, Type GRH, —general rapid hardening, for use when the higher strength properties of Type VRH or a Type MRH cement is not required. “ASTM C1600 lists minimum requirements for compressive strength, setting time, shrinkage and soundness (autoclave expansion),” says Hicks. “Optional specifications for sulfate expansion, alkali silicate reactions with aggregates, heat of hydration and expansion in water are also…
-
A recently approved revision to ASTM International standard C 150 , Specification for Portland Cement, includes three significant technical changes to the document. The changes are part of a joint effort between ASTM and the American Association of State and Highway and Transportation Officials to harmonize C 150 with AASHTO’s standard, M 85, Specification for Portland Cement. C 150 is under the…
-
ASTM International Committee B08 on Metallic and Inorganic Coatings has recently approved a revision of one of its most important standards, B 633 , Specification for Electrodeposited Coatings of Zinc on Iron and Steel. B 633 is under the jurisdiction of Task Group B08.08.04 on Soft Metals, which is part of Subcommittee B08.08 on Metallic Coatings. Zinc coatings are used to provide a sacrificial…
-
If you are a user of ASTM B 456, Specification for Electrodeposited Coatings of Copper Plus Nickel Plus Chromium and Nick Plus Chromium, ASTM International Committee B08 on Metallic and Inorganic Coatings would like to hear from you. B 456 is under the jurisdiction of Subcommittee B08.08.03 on Decorative Coatings. "Subcommittee B08.08.03 has received reports that some users are experiencing…
-
After a 35-year-absence, the natural cement industry is being revived and, along with it, a long-withdrawn ASTM International standard. Until it closed in 1970, the Century Cement Company in Rosendale, N.Y. was the last company to manufacture natural cement. Up to that point, Rosendale had been the center of the industry, the source of more than half of all natural cement produced in the U.S.…
-
A new test method developed by ASTM International Committee C01 on Cement provides information about the behavior of cement that can be used in the process of selecting cementing materials for specific applications. The standard, C 1608, Test Method for Chemical Shrinkage of Hydraulic Cement Pastes, is under the jurisdiction of Subcommittee C01.31 on Volume Change. Test Method C 1608 was…
-
ASTM International Committee D33 on Protective Clothing and Lining Work for Power Generation Facilities has approved a revision to standard D 4260, now titled Practice for Liquid and Gelled Acid Etching of Concrete. The revised standard is under the jurisdiction of Subcommittee D33.05 on Application and Surface Preparation. According to Tamryn Doolan, president and CEO, Surface Gel Tek, the…