Search
Advanced search
Filter by category
Filter by committee
Search results
-
Increasing interest in the various uses of electrical contacts is the leading impetus for the development of a proposed new standard, ASTM WK34423 , Specification for Electrodeposited Coatings of Palladium-Cobalt Alloy for Engineering Use. The proposed standard is being developed by Subcommittee B08.08 on Metallic Coatings , part of ASTM International Committee B08 on Metallic and Inorganic…, ASTM Committee B08 Next Meeting:, May 10, 2012, May Committee Week, Phoenix, Ariz., Technical Contact:, Sheikh H. Rahman, Lean Corp., Southfield, Mich., Phone: 248-447-1526; srahman@lear.com, ASTM Staff Contact:, Diane Trinsey, Phone: 610-832-9661; dtrinsey@astm.org, ASTM PR Contact:, Barbara Schindler, Phone: 610-832-9603; bschindl@astm.org Release #9016
-
A new ASTM International practice provides a standard for preparing a mixture of cement paste that will simulate the shearing experienced by the cement paste in concrete. The new standard, ASTM C1738 , Practice for High-Shear Mixing of Hydraulic Cement Pastes, was developed by Subcommittee C01.22 on Workability , part of ASTM International Committee C01 on Cement . According to Chiara Ferraris,…
-
A new ASTM subcommittee seeks to acknowledge the ongoing advances being made in the field of nanostructured inorganic coatings. B08.16 on Nanostructured Coatings, part of ASTM International Committee B08 on Metallic and Inorganic Coatings, is currently developing its first proposed standard, ASTM WK29468 , Specification for Galvanic Protection of Steel Using a Nanostructured Coating of 95 % Zinc…
-
Rapid hardening hydraulic cements are used in a variety of applications in which reduced cementitious contents are desired or early service is needed. Included among these applications are paving, construction, stucco, mortar and block. A newly approved ASTM International standard covering these cements, ASTM C1600/C1600M , Specification for Rapid Hardening Hydraulic Cement, has been developed by…, Type URH, —ultra rapid hardening, for use where ultra high early strength is desired;, Type VRH, —very rapid hardening, for use where very high early strength is desired;, Type MRH, —medium rapid hardening, for use where mid-range rapid hardening, high early strength is desired; and, Type GRH, —general rapid hardening, for use when the higher strength properties of Type VRH or a Type MRH cement is not required. “ASTM C1600 lists minimum requirements for compressive strength, setting time, shrinkage and soundness (autoclave expansion),” says Hicks. “Optional specifications for sulfate expansion, alkali silicate reactions with aggregates, heat of hydration and expansion in water are also…
-
No industry standard currently exists that addresses the vacuum sealing requirements of knife-edged flanges for high vacuum applications. Existing international standards focus on interchangeability of the hardware, but do not address the reliability of the seal. ASTM International Committee E42 on Surface Analysis is now working on a proposed standard on the subject, WK21206 , Specification…
-
A 2002 workshop on galling wear held by ASTM International Committee G02 on Wear and Erosion provided the impetus for the development of a new standard, ASTM G196 , Test Method for Galling Resistance of Material Couples. The new standard is under the jurisdiction of Subcommittee G02.40 on Non-Abrasive Wear. According to Scott Hummel, Ph.D., associate professor, head of the department of…
-
While the continuous quality verification concept is still quite new, it has the potential to become an important approach to assuring product quality in the pharmaceutical industry. With this in mind, ASTM International Committee E55 on Manufacture of Pharmaceutical Products has approved a new standard, E2537 , Guide for Application of Continuous Quality Verification to Pharmaceutical and…
-
ASTM International Committee E55 on Manufacture of Pharmaceutical Products has developed a new standard that covers the life cycle of pharmaceutical and biopharmaceutical manufacturing systems. The new standard, E 2500 , Guide for Specification, Design and Verification of Pharmaceutical and Biopharmaceutical Manufacturing Systems and Equipment, is under the jurisdiction of Subcommittee E55.03 on…
-
A recently approved revision to ASTM International standard C 150 , Specification for Portland Cement, includes three significant technical changes to the document. The changes are part of a joint effort between ASTM and the American Association of State and Highway and Transportation Officials to harmonize C 150 with AASHTO’s standard, M 85, Specification for Portland Cement. C 150 is under the…
-
The ASTM International committee formerly known as E55 on Pharmaceutical Application of Process Analytical Technology has undergone a change in title and scope that reflects the intent of the committee to be more inclusive of all the tools, instrumentation and sciences that might be used by the industry in the management of pharmaceutical manufacturing processes. The committee is now known as E55…