Search
Advanced search
Filter by category
Filter by committee
Search results
-
A newly approved ASTM copper standard focuses on the mechanical properties of machining brasses. ASTM B981/B981M , Specification for Low Leaded Brass Rod, Bar and Shapes, was developed by Subcommittee B05.02 on Rod, Bar, Wire, Shapes and Forgings , part of ASTM International Committee B05 on Copper and Copper Alloys . “Since 1997, there has been increasing legislation, regulation and voluntary…, ASTM Committee B05 Next Meeting:, April 15-17, 2013, April Committee Week, Indianapolis, Ind., Technical Contact:, Larry Muller, Chase Brass and Copper Co., Montpelier, Ohio, Phone: 419-485-8932; lmuller@chasebrass.com, ASTM Staff Contact:, Jennifer Rodgers, Phone: 610-832-9694; jrodgers@astm.org, ASTM PR Contact:, Barbara Schindler, Phone: 610-832-9603; bschindl@astm.org R elease #9307
-
A new ASTM International standard will provide gasket manufacturers a test for measuring creep and compression that can be used for R&D and material comparisons, and as a quality assurance tool. ASTM F2837 , Test Method for Hot Compression Properties of Gasket Materials, was developed by Subcommittee F03.40 on Chemical Test Methods, under the jurisdiction of ASTM International Committee F03…, ASTM Committee F03 Next Meeting:, Oct 12-13, October Committee Week, San Antonio, Texas, Technical Contact:, James Lingenfelder, Gasket Resources Inc., Houston, Texas, Phone: 713-856-9445; jtling@durlon.com, ASTM Staff Contact:, Joseph Hugo, Phone: 610-832-9740; jhugo@astm.org, ASTM PR Contact:, Barbara Schindler, Phone: 610-832-9603; bschindl@astm.org Release #8695/Sept2010
-
Flow characteristics of fine metal powders are important in filling dies for pressing of powder metallurgy compacts, which are later sintered and sometimes machined into finished parts. The flow rate, as measured by a new ASTM standard, determines the flow necessary for a precise quantity of powder to be introduced into the die. The new standard, B964 , Test Methods for Flow Rate of Metal Powders…
-
Two recently approved ASTM International standards provide user-friendly tests for properties of sintered metallurgy products. The new standards, developed by Subcommittee B09.04 on Bearings, are ASTM B962 , Test Methods for Density of Compacted or Sintered Power Metallurgy (PM) Products Using Archimedes’ Principle, and ASTM B963 , Test Methods for Oil Content, Oil-Impregnation Efficiency and…
-
ASTM International Committee F03 on Gaskets has developed and approved a new standard that can be used to evaluate gasket materials covered by ASTM F104 , Classification System for Nonmetallic Gasket Materials. The new standard, F2716 , Practice for Comparison of Nonmetallic Flat Gaskets in High Pressure Saturated Steam, is under the jurisdiction of Subcommittee F03.10 on Composite Gaskets. ASTM…
-
A new ASTM International standard responds to a recent emphasis by regulatory agencies that firms manufacturing drug products demonstrate the efficacy of disinfectants used in controlled environments. The standard, ASTM E2614 , Guide for Evaluation of Cleanroom Disinfectants, was developed by Subcommittee E35.15 on Antimicrobial Agents, part of ASTM International Committee E35 on Pesticides and…
-
ASTM International Committee B05 on Copper and Copper Alloys has created a new task group, TG9018, which will be focused on the Antimicrobial Applications of Copper and Copper Alloys. The task group was formed following the U.S. Environmental Protection Agency's announcement of its registration of copper alloys as antimicrobial materials with specific health claims. According to James Michel,…
-
A proposed new standard being developed by ASTM International Committee B09 on Metal Powders and Metal Powder Products offers a solution to the challenge of handling and characterizing very fine powders. Subcommittee B09.02 on Base Metal Powders is developing the proposed standard, WK13023 , Test Method for Determination of Tap Density of Metallic Powders by a Constant Volume Measuring Method. …
-
Conventionally processed powder metallurgy materials often exhibit open microporosity at the surface. While it is a natural part of the process, this microporosity can affect the measurement of surface finishes. To cover this and other issues that arise from measuring the surface finish of powder metallurgy, ASTM International Committee B09 on Metal Powders and Metal Powder Products has developed…
-
ASTM International Committee F16 on Fasteners has recently approved an important new standard that deals with coated threaded fasteners and washers by hot-dip zinc galvanizing. The standard, F 2329, Specification for Zinc Coating, Hot-Dip, Requirements for Application to Carbon and Alloy Steel Bolts, Screws, Washers, Nuts and Special Threaded Fasteners, is under the jurisdiction of Subcommittee…