Search
Advanced search
Filter by category
Filter by committee
Search results
-
Two new ASTM International standards on rescue litters and fixed anchorages will contribute to the safety and efficiency of search and rescue operations. Both standards were developed by Subcommittee F32.01 on Equipment, Testing and Maintenance, part of ASTM International Committee F32 on Search and Rescue., BASKET TYPE RESCUE LITTERS, Until the development of ASTM F2821 , Test Methods for Basket Type Rescue Litters, there had not been a standardized means for manufacturers to test these rescue devices, according to John McKently, Los Angeles County Sheriff's Department, and an F32 member. “ASTM F2821 was developed because there was no standard available that allowed manufacturers to test litter products in the same way,” says…, FIXED ANCHORAGES, According to McKently, the impetus for the development of ASTM F2822 , Specification for Fixed Anchorages Installed on Structures Used for Rope Rescue Training, was similar to that of ASTM F2821. In this case, the standard was developed to provide minimum strength requirements for anchorages permanently installed or attached to training towers or other structures used for rope rescue training. “…, ASTM Committee F32 Next Meeting:, Nov. 7-10, in conjunction with the International Technical Rescue Symposium, Golden, Colo., Technical Contact:, John McKently, Los Angeles County Sheriff's Department, Glendale, Calif., Phone: 818-247-3209; jmckently@earthlink.net, ASTM Staff Contact:, Thomas O'Toole, Phone: 610-832-9739; totoole@astm.org, ASTM PR Contact:, Barbara Schindler, Phone: 610-832-9603; bschindl@astm.org Release #8654
-
Rapid hardening hydraulic cements are used in a variety of applications in which reduced cementitious contents are desired or early service is needed. Included among these applications are paving, construction, stucco, mortar and block. A newly approved ASTM International standard covering these cements, ASTM C1600/C1600M , Specification for Rapid Hardening Hydraulic Cement, has been developed by…, Type URH, —ultra rapid hardening, for use where ultra high early strength is desired;, Type VRH, —very rapid hardening, for use where very high early strength is desired;, Type MRH, —medium rapid hardening, for use where mid-range rapid hardening, high early strength is desired; and, Type GRH, —general rapid hardening, for use when the higher strength properties of Type VRH or a Type MRH cement is not required. “ASTM C1600 lists minimum requirements for compressive strength, setting time, shrinkage and soundness (autoclave expansion),” says Hicks. “Optional specifications for sulfate expansion, alkali silicate reactions with aggregates, heat of hydration and expansion in water are also…
-
ASTM International Committee F32 on Search and Rescue is currently developing a number of proposed new standards. Two of the proposed standards under the jurisdiction of Subcommittee F32.02 on Management and Operations are WK23984 , Guide for Level 1 (Basic) Mounted Search and Rescue (MSAR) Responder, and WK24699, Guide for Training for Land SAR as a Level 1 Out of Area Disaster Responder.…
-
The importance of telecommunicators in the search and rescue field cannot be overstated. Dispatchers receiving and delivering accurate information in a timely manner are critical to any SAR operation. A new standard developed by ASTM International Committee F32 on Search and Rescue highlights the importance of proper training for SAR dispatchers. The standard, ASTM F2662 , Guide for Minimum…
-
ASTM International Committee F03 on Gaskets has developed and approved a new standard that can be used to evaluate gasket materials covered by ASTM F104 , Classification System for Nonmetallic Gasket Materials. The new standard, F2716 , Practice for Comparison of Nonmetallic Flat Gaskets in High Pressure Saturated Steam, is under the jurisdiction of Subcommittee F03.10 on Composite Gaskets. ASTM…
-
A new ASTM International standard responds to a recent emphasis by regulatory agencies that firms manufacturing drug products demonstrate the efficacy of disinfectants used in controlled environments. The standard, ASTM E2614 , Guide for Evaluation of Cleanroom Disinfectants, was developed by Subcommittee E35.15 on Antimicrobial Agents, part of ASTM International Committee E35 on Pesticides and…
-
A recently approved revision to ASTM International standard C 150 , Specification for Portland Cement, includes three significant technical changes to the document. The changes are part of a joint effort between ASTM and the American Association of State and Highway and Transportation Officials to harmonize C 150 with AASHTO’s standard, M 85, Specification for Portland Cement. C 150 is under the…
-
Two proposed new ASTM International standards are part of the extensive work being done by Committee F32 on Search and Rescue to develop a comprehensive set of standards for search and rescue team training. The proposed new standards, WK15661 , Guide for Level I Rope Rescue Technician Endorsement, and WK15503 , Guide for Training of Level I Rescue Technician, are both under the jurisdiction of…
-
ASTM International Committee A06 on Magnetic Properties has approved the first in a series of proposed standards on permanent magnet materials. The new standard, A 1054 , Specification for Sintered Ceramic Ferrite Permanent Magnets, as well as the other proposed standards, are under the jurisdiction of Subcommittee A06.02 on Material Specifications. While ASTM has long had standards covering…
-
After a 35-year-absence, the natural cement industry is being revived and, along with it, a long-withdrawn ASTM International standard. Until it closed in 1970, the Century Cement Company in Rosendale, N.Y. was the last company to manufacture natural cement. Up to that point, Rosendale had been the center of the industry, the source of more than half of all natural cement produced in the U.S.…