Search
Advanced search
Filter by category
Filter by committee
Search results
-
ASTM C1264 Addresses Origin and Source Labeling of Drywall and Other Gypsum Products, In response to the importation of contaminated drywall that caused health and safety hazards when used in home construction, the Drywall Safety Act of 2012 (PL 112-266) was signed into law by President Barack Obama on Jan. 14, 2013. The new law cites ASTM International standard C1264-11 , Specification for Sampling, Inspection, Rejection, Certification, Packaging, Marking, Shipping, Handling and…, Labeling, The Drywall Safety Act requires the CPSC to set regulations based on C1264 , which was developed by ASTM Subcommittee C11.01 on Specifications and Test Methods for Gypsum Products , part of ASTM Committee C11 on Gypsum and Related Building Materials and Systems . The standard provides the CPSC, states, suppliers and consumers with an effective tool for supply chain communication by specifying…, Up-to-Date Standards, Under the act’s provisions, ASTM International will notify the CPSC of any updates to the labeling standard within 60 days; the CPSC will then have 90 days to disapprove ASTM’s recommended changes. If the CPSC accepts the most updated version of the ASTM standard, then the new version becomes effective 180 days after ASTM’s initial notification., Sulfur Content, Because sulfur content levels in drywall have been associated with elevated corrosion rates in a home, the act requires that the CPSC issue a regulation that limits the sulfur content for drywall manufactured in the United States or imported from abroad. In lieu of issuing a federal rule, the CPSC may adopt a voluntary consensus standard, developed by C11.01, that addresses the level of sulfur…, ASTM Staff Contact:, Thomas O’Toole, Phone: 610-832-9739; totoole@astm.org, ASTM PR Contact:, Barbara Schindler, Phone: 610-832-9603; bschindl@astm.org Release #9277
-
In a quest for lighter, more crash-resistant and fuel-efficient vehicles, the automobile and steel industries are developing steel sheets that have higher alloy content, and thus more complex hardening mechanisms, than sheets currently being used. The sheets, known generally as advanced high-strength steels, are covered by a new ASTM International standard, ASTM A1079 , Specification for Steel…, ASTM Committee A05 Next Meeting:, Nov. 11-13, November Committee Week, Atlanta, Ga., Technical Contact:, Gary Dallin, GalvInfo Center, International Zinc Association, Burlington, Ontario, Canada, Phone: 905-315-7443; gdallin@cogeco.ca, ASTM Staff Contact:, Kristy Straiton, Phone: 610-832-9640; kstraiton@astm.org, ASTM PR Contact:, Barbara Schindler, Phone: 610-832-9603; bschindl@astm.org R elease #9304
-
A new ASTM International standard that will help ensure the accurate use of micrometers in the measurement of a type of steel sheet has been developed and approved by ASTM International Committee A05 on Metallic-Coated Iron and Steel Products . ASTM A1073/A1073M , Practice for Using Hand Micrometers to Measure the Thickness of Nonmetallic and Metallic-Coated Steel Sheet, is under the…, ASTM Committee ASTM Committee A05 Next Meeting:, Nov. 11-13, 2012, November Committee Week, Atlanta, Ga., Technical Contact:, Herbert W. Koch, Harris Steel Co., Chicago, Ill., Phone: 708-656-5500; hkoch@harrissteelco.com, ASTM Staff Contact:, Kristy Straiton, Phone: 610-832-9640; kstraiton@astm.org, ASTM PR Contact:, Barbara Schindler, Phone: 610-832-9603; bschindl@astm.org R elease #9254
-
ASTM International Committee F41 on Unmanned Maritime Vehicle Systems will meet on Aug. 17, 2011, at the Walter E. Washington Convention Center in Washington, D.C. The meeting will take place in conjunction with the AUVSI Unmanned Systems North American 2011 Conference. The F41 executive subcommittee meeting will begin at 7:00 a.m. on Aug. 17. in room 149A. In addition, all interested parties are…
-
Owners and specifiers of steel building projects will be the primary users of a new ASTM International standard, ASTM A1068 , Practice for Life-Cycle Cost Analysis of Corrosion Protection Systems on Iron and Steel Products. The new standard was developed by Subcommittee A05.13 on Structural Shapes and Hardware Specifications, part of ASTM International Committee A05 on Metallic-Coated Iron and…
-
Several years ago, a housing boom followed by recovery from damage caused by Hurricane Katrina and other storms created a surge in the use of imported drywall in the United States, particularly in the southeastern area of the country. However, since then, there have been a number of complaints concerning corrosion and odors in homes in which some of this drywall was used. Interim guidance…
-
Subcommittee A05.13 on Structural Shapes and Hardware Specifications is currently working on proposed new standards that would be used by engineers and architects who design with steel fabrications. These proposed standards will be used to evaluate the costs of steel construction over the lifetime of a project and to compare different corrosion protection systems on their impact to this lifetime…
-
With heightened interest in issues involving corrosive gypsum board, the first draft of a proposed new standard on the subject, ASTM WK26072 , Practice for Evaluation of Buildings to Identify Corrosive Gypsum Board, was reviewed and edited at a task group meeting on Nov. 10 in Atlanta, Ga. The proposed new standard is under the jurisdiction of ASTM Subcommittee C11.01 on Specifications and Test…, ASTM Committee C11 Next Meeting:, May 17-19, 2010, St. Louis, Mo., Technical Contact:, Spiderman Mulholland, U.S. Building Consultants Inc., Gainesville, Fla., Phone: 352-505-6771; spiderman@usbcinc.com, ASTM Staff Contact:, Thomas O’Toole, Phone: 610-832-9739; totoole@astm.org, ASTM PR Contact:, Barbara Schindler, Phone: 610-832-9603; bschindl@astm.org Release #8414/Nov2009
-
At an ASTM International meeting held on Oct. 20 it was decided to initiate the formulation of a proposed new ASTM standard that will cover issues relating to drywall and indoor air quality. Representatives from various ASTM International committees, including C11 on Gypsum and Related Building Materials and Systems and E06 on Performance of Buildings attended the meeting, which was held during…
-
Flow characteristics of fine metal powders are important in filling dies for pressing of powder metallurgy compacts, which are later sintered and sometimes machined into finished parts. The flow rate, as measured by a new ASTM standard, determines the flow necessary for a precise quantity of powder to be introduced into the die. The new standard, B964 , Test Methods for Flow Rate of Metal Powders…