Search
Advanced search
Filter by category
Filter by committee
Search results
-
ASTM International is developing a proposed standard that will help manufacturers of automatic guided industrial vehicles evaluate their products. In addition to manufacturers, vehicle buyers will use this standard (WK48955: Test Method for Docking and Navigation for Driverless Automatic Guided Industrial Vehicles) to conduct their own tests on potential purchases. ASTM member Roger Bostelman is…, Media Inquiries:, Nathan Osburn, tel +1.610.832.9603; nosburn@astm.org, Technical Contact:, Roger V. Bostelman, National Institute of Standards and Technology, Gaithersburg, Md., tel +1.301.975.3426; roger.bostelman@nist.gov, ASTM Staff Contact:, Pat Picariello, tel +1.610.832.9720; ppicariello@astm.org Release #9811 ###
-
ASTM International has launched a new technical committee, F45 on Driverless Automatic Guided Industrial Vehicles . After organizational meetings in October 2013 and January 2014, F45 was approved at the board of director’s recent spring meeting. In use since 1953, automated guided vehicles (AGVs) are defined by the Material Handling Institute (MHI) as “computer-controlled wheel-based load…, Technical Contact:, Roger Bostelman, National Institute of Standards and Technology, Gaithersburg, Md., roger.bostelman@nist.gov , ASTM Staff Contact:, Pat Picariello, Phone: 610-832-9720; ppicariello@astm.org, ASTM PR Contact:, Barbara Schindler, Phone: 610-832-9603; bschindl@astm.org Release #9650
-
A new ASTM International standard will provide gasket manufacturers a test for measuring creep and compression that can be used for R&D and material comparisons, and as a quality assurance tool. ASTM F2837 , Test Method for Hot Compression Properties of Gasket Materials, was developed by Subcommittee F03.40 on Chemical Test Methods, under the jurisdiction of ASTM International Committee F03…, ASTM Committee F03 Next Meeting:, Oct 12-13, October Committee Week, San Antonio, Texas, Technical Contact:, James Lingenfelder, Gasket Resources Inc., Houston, Texas, Phone: 713-856-9445; jtling@durlon.com, ASTM Staff Contact:, Joseph Hugo, Phone: 610-832-9740; jhugo@astm.org, ASTM PR Contact:, Barbara Schindler, Phone: 610-832-9603; bschindl@astm.org Release #8695/Sept2010
-
No industry standard currently exists that addresses the vacuum sealing requirements of knife-edged flanges for high vacuum applications. Existing international standards focus on interchangeability of the hardware, but do not address the reliability of the seal. ASTM International Committee E42 on Surface Analysis is now working on a proposed standard on the subject, WK21206 , Specification…
-
A 2002 workshop on galling wear held by ASTM International Committee G02 on Wear and Erosion provided the impetus for the development of a new standard, ASTM G196 , Test Method for Galling Resistance of Material Couples. The new standard is under the jurisdiction of Subcommittee G02.40 on Non-Abrasive Wear. According to Scott Hummel, Ph.D., associate professor, head of the department of…
-
ASTM International Committee F03 on Gaskets has developed and approved a new standard that can be used to evaluate gasket materials covered by ASTM F104 , Classification System for Nonmetallic Gasket Materials. The new standard, F2716 , Practice for Comparison of Nonmetallic Flat Gaskets in High Pressure Saturated Steam, is under the jurisdiction of Subcommittee F03.10 on Composite Gaskets. ASTM…
-
A new ASTM International standard responds to a recent emphasis by regulatory agencies that firms manufacturing drug products demonstrate the efficacy of disinfectants used in controlled environments. The standard, ASTM E2614 , Guide for Evaluation of Cleanroom Disinfectants, was developed by Subcommittee E35.15 on Antimicrobial Agents, part of ASTM International Committee E35 on Pesticides and…
-
ASTM International Committee E42 on Surface Analysis has approved a new standard, E 2382, Guide to Scanner and Tip Related Artifacts in Scanning Tunneling Microscopy and Atomic Force Microscopy. The guide, under the jurisdiction of Subcommittee E42.14 on STM/AFM, was proposed in order to assist new scanning probe microscopy users with more rapid recognition and assessment of artifacts in imaging…