Search
Advanced search
Filter by category
Filter by committee
Search results
-
In light of COVID-19 (coronavirus) and growing safety concerns for members and staff, ASTM International announced today that previously scheduled April standards development meetings in Boston (March 29-April 3) and Prague (April 27-30) have been canceled. The decision was based on several factors, including, but not limited to: Continued review of information and recommendations from the U.S.…, Media Inquiries:, Dan Bergels, tel +1.610.832.9602; dbergels@astm.org Release #10993
-
A new ASTM International standard outlines minimum requirements for designing, manufacturing, and installing emergency parachute systems that help recover a small plane’s airframe, potentially helping occupants survive, according to Jay Yeakle, a member of ASTM International’s general-aviation aircraft committee (F44) and who serves as an administrator at Cirrus Aircraft. “Whole aircraft…, Media Inquiries:, Dan Bergels, tel +1.610.832.9602; dbergels@astm.org, Committee Contact:, Joe Koury, tel +1.610.832.9804; jkoury@astm.org Release #10975
-
A proposed ASTM International standard will provide guidance for using geocells – open-celled geosynthetics that help hold soils and rocks in place – in roadway projects. Geocells are commonly used in road construction, earth retention, and other construction projects. According to ASTM International member Eli Cuelho, there is currently no standard for using geocells in geotechnical and…, Media Inquiries:, Dan Bergels, tel +1.610.832.9602; dbergels@astm.org, Committee Contact:, Katerina Koperna, tel +1.610.832.9728; kkoperna@astm.org Release #10955
-
A new ASTM International standardized practice will help determine “water loads,” that occur during landing, taxiing, and takeoffs for water-based aircraft. These planes must be able to safely react to the water loads, which are based on an aircrafts’ operating characteristics. “The standard provides clear instructions on how to determine the required loads for either dual float equipped planes…, Media Inquiries:, Dan Bergels, tel +1.610.832.9602; dbergels@astm.org, Committee Contact:, Joe Koury, tel +1.610.832.9804; jkoury@astm.org Release #10646
-
A new ASTM International standard will help those who construct and install geosynthetic clay liners (GCLs), which are used to help with containment for: landfills; coal combustion residual storage cells; mining operations; and, remediation and environmental protection projects. The new standard ( D8204 ) focuses on evaluating both best practices as well as possible negative impacts of installing…, Media Inquiries:, Dan Bergels, tel +1.610.832.9602; dbergels@astm.org, Committee Contact:, Katerina Koperna, tel +1.610.832.9728; kkoperna@astm.org Release #10612
-
A new ASTM International standard aims to enhance small aircraft safety by supporting non-essential ice detectors. The new specification ( F3310 ) was developed by ASTM International’s committee on general aviation aircraft ( F44 ). According to ASTM International member Dennis Regnier, CAV Ice Protection, such devices can help notify a pilot when the plane encounters icing conditions. “…, Media Inquiries:, Dan Bergels, tel +1.610.832.9602; dbergels@astm.org, Committee Contact:, Joe Koury, tel +1.610.832.9804; jkoury@astm.org Release #10549
-
A new ASTM International standard supports geosynthetic cementitious composite mats (GCCM), a new family of materials that can help control erosion, protect slopes and berms, and line ditches and culverts. The new standard ( D8173 ) identifies proper layout, installation and hydration procedures for GCCM. It also describes equipment for designers, inspectors, and installers as well as provides a…, Media Inquiries:, Dan Bergels, tel +1.610.832.9602; dbergels@astm.org, Committee Contact:, Katerina Koperna, tel +1.610.832.9728; kkoperna@astm.org Release #10513
-
Pending approval from its board of directors, ASTM International announced yesterday the launch of a new committee focused on creating technical standards and guidance materials for cannabis and its products and processes. Yesterday, about 60 industry representatives, associations, and others convened at ASTM International’s global headquarters near Philadelphia and decided to create a volunteer…, Media Inquiries:, Nate Osburn, tel +1.610.832.9603; nosburn@astm.org, Committee Contact:, Robert Morgan, tel +1.610.832.9732; rmorgan@astm.org Release #10266
-
By request from industry, ASTM International will host an organizational meeting to potentially create a new technical committee that develops voluntary consensus standards for cannabis. The no-fee meeting is Tuesday, Feb. 28, at 9 a.m. EST at ASTM International’s global headquarters in, West Conshohocken, Pa., USA. Industry stakeholders and others interested in charting a path towards voluntary…, ASTM Cannabis Organizational Meeting:, Feb. 28, 2017, ASTM International, 100 Barr Harbor Drive, West Conshohocken, PA, 19428-2959 USA, Media Inquiries:, Nate Osburn, tel +1.610.832.9603; nosburn@astm.org, ASTM Staff Contact:, Christine DeJong, tel +1.610.832.9736; cdejong@astm.org Release #10251
-
Yesterday, more than 50 government and industry officials decided to launch a new ASTM International committee dedicated to developing standards in the area of commercial spaceflight. The Committee on Commercial Spaceflight (F47) will focus on standards development in areas such as occupant safety of orbital and suborbital vehicles, launch and reentry vehicles, and spaceports. James Thomas,…, Media Inquiries:, Dan Bergels, tel +1.610.832.9602; dbergels@astm.org, ASTM Staff Contact:, Kristy Straiton, tel +1.610.832.9640; kstraiton@astm.org Release #10195