Search
Advanced search
Filter by category
Filter by committee
Search results
-
A new ASTM International standard will provide a specification for low density poly vinylidene fluoride (PVDF) based materials intended for use in wire and cable jacketing. ASTM’s committee on electrical and electronic insulating materials (D09) developed the standard, which will be soon published as D8318. Low density PVDF cable jacketing is a new product that has the potential to offer…, Media Inquiries:, Dan Bergels, tel +1.610.832.9602; dbergels@astm.org, Committee Contact:, Alyson Fick, tel +610.832.9710; afick@astm.org Release #11058 ###
-
In light of COVID-19 (coronavirus) and growing safety concerns for members and staff, ASTM International announced today that previously scheduled April standards development meetings in Boston (March 29-April 3) and Prague (April 27-30) have been canceled. The decision was based on several factors, including, but not limited to: Continued review of information and recommendations from the U.S.…, Media Inquiries:, Dan Bergels, tel +1.610.832.9602; dbergels@astm.org Release #10993
-
ASTM International’s Committee D09 (Electrical and Electronic Insulating Materials) invites anyone to join in developing a new standard to help maintain the integrity of cables during an emergency such as a fire. Specifically, the proposed standard (WK52230, Test Method for Determination of Acid Gas Content of Wire and Cable Insulation or Jacket Material) will help determine the halogen content…, ASTM Committee D09 Next Meeting:, April 14-15, 2016, April Committee Week, San Antonio, Texas, Media Inquiries:, Nathan Osburn, tel +1.610.832.9603; nosburn@astm.org, Technical Contact:, Larry Ingram, Williamsport, Pa., tel +1.570.916.8448; larry77151@comcast.net , ASTM Staff Contact:, Katerina Koperna, tel +1.610.832.9728; kkoperna@astm.org Release #9960
-
No industry standard currently exists that addresses the vacuum sealing requirements of knife-edged flanges for high vacuum applications. Existing international standards focus on interchangeability of the hardware, but do not address the reliability of the seal. ASTM International Committee E42 on Surface Analysis is now working on a proposed standard on the subject, WK21206 , Specification…
-
A 2002 workshop on galling wear held by ASTM International Committee G02 on Wear and Erosion provided the impetus for the development of a new standard, ASTM G196 , Test Method for Galling Resistance of Material Couples. The new standard is under the jurisdiction of Subcommittee G02.40 on Non-Abrasive Wear. According to Scott Hummel, Ph.D., associate professor, head of the department of…
-
An ASTM International task group on battery separator materials is currently working on the latest in a series of standards being developed for alkaline battery separators. The proposed new standard, WK13587 , Test Methods for Sampling and Testing Materials That Are Used for Alkaline Battery Separators, is under the jurisdiction of Subcommittee D09.19 on Dielectric Sheet and Roll Products, which…
-
Two newly approved ASTM standards are filling a gap that has existed for tests for battery separators. The new standards, D 7129, Test Method for Determination of Ammonia Trapping in a Grafted Battery Separator, and D 7131, Test Method for Determination of Ion Exchange Capacity (IEC) in a Grafted Battery Separator, are under the jurisdiction of Subcommittee D09.19 on Dielectric Sheet and Roll…
-
ASTM International Committee D09 on Electrical and Electronic Insulating Materials will host a presentation of the European Unions Restriction of Hazardous Substances (RoHS) Directive during their meeting in Philadelphia, Pa. on March 15. The meeting will run from 3:00 to 5:00 p.m. and will be followed by a social hour. Electrical equipment marketed in the EU after July 1, 2006, must comply…
-
ASTM International Committee E42 on Surface Analysis has approved a new standard, E 2382, Guide to Scanner and Tip Related Artifacts in Scanning Tunneling Microscopy and Atomic Force Microscopy. The guide, under the jurisdiction of Subcommittee E42.14 on STM/AFM, was proposed in order to assist new scanning probe microscopy users with more rapid recognition and assessment of artifacts in imaging…