Search
Advanced search
Filter by category
Filter by committee
Search results
-
ASTM Pervious Concrete Subcommittee Developing Proposed Standard for Sustainable Mixture ProportionsOnce approved, a proposed new ASTM standard will aid concrete producers in developing sustainable and durable mixture proportions for pervious concrete. The proposed new standard, WK23367 , Test Method for Evaluating the Surface Durability Potential of a Pervious Concrete Mixture, is being developed by Subcommittee C09.49 on Pervious Concrete, part of ASTM International Committee C09 on Concrete…
-
A proposed new ASTM International standard, ASTM WK22233 , Test Method for Indication of Concrete’s Ionic Conductivity, describes a five-minute nondestructive test that has the potential to replace a destructive six-hour test requiring several hours of preparation time. The proposed standard is being developed by Subcommittee C09.66 on Concrete’s Resistance to Fluid Penetration, part of ASTM…
-
Shrinkage that occurs during the drying process is a major cause of cracking in concrete. However, application of shrinkage-reducing admixtures in the field has been yielding positive results, and engineers have realized that admixtures can mitigate cracking. A new ASTM standard currently being developed by Subcommittee C09.23 on Chemical Admixtures will set minimum standards for an admixture to…
-
More effective quality testing of the synthetic, hollow filaments that are often used in the manufacture of lower cost paintbrushes is the purpose of a new standard approved by ASTM International Committee D01 on Paint and Related Coatings, Materials and Applications. The new standard, ASTM D7233 , Test Method for Testing Fracture of Level Paintbrush Filaments, was developed by Subcommittee D01.…
-
The wettability of a particular solid coating, substrate or pigment on a surface is a key to its effectiveness, as wetting is important to adhesion as well as to the prevention of surface defects such as craters, dewetting and crawling. A new ASTM International standard uses contact angle measurements to determine the wettability of coatings. The new standard, D7490 , Test Method for Measurement…
-
By necessity, paint used for roadway applications needs to dry quickly. Some multi-component traffic paints cure in less than 10 minutes, some much faster. Because of this speed of curing, these traffic paints and other types of fast-cure (less than 10 minutes) multi-component paints cannot be tested for volatile content using procedures outlined in the ASTM International standard typically used…
-
Because of its porous nature, pervious concrete cannot be tested using standards developed for traditional concrete. In order to fill this need, ASTM International Committee C09 on Concrete and Concrete Aggregates is developing a series of proposed test methods specific to pervious. The first of these proposed standards, ASTM C1688/C1688M , Test Method for Density and Void Content of Freshly…
-
Two new calibration standards for use with X-ray fluorescence equipment in the chemical analysis of hydraulic cement are now available from the Cement and Concrete Reference Laboratory (CCRL). The new standards are designated Portland Cements 167 and 168 and are vacuum-sealed to prevent moisture uptake. Robin Haupt, supervisor, CCRL proficiency sample program, says that the two new cements were…
-
Two new standards demonstrate the broad range of practices and test methods currently being developed by ASTM International Committee D01 on Paint and Related Coatings, Materials and Applications. The new ASTM standards will be used in the realms of color reproduction and contact angle measurement. Achieving Consistent Color Reproduction Developed by Subcommittee D01.56 on Printing Inks, ASTM…
-
ASTM Committee D01 on Paint and Related Coatings, Materials and Applications will present a technical seminar, “New Solvents and Formulating Techniques for Low VOC and HAP Paints,” on Sunday, June 15, 2008, from 4 to 6 p.m., at the Hyatt Regency Hotel in Vancouver, British Columbia, Canada. The seminar will be held in conjunction with the D01 committee meeting to be held June 15-18 in Vancouver…