Search
Advanced search
Filter by category
Filter by committee
Search results
-
Rapid hardening hydraulic cements are used in a variety of applications in which reduced cementitious contents are desired or early service is needed. Included among these applications are paving, construction, stucco, mortar and block. A newly approved ASTM International standard covering these cements, ASTM C1600/C1600M , Specification for Rapid Hardening Hydraulic Cement, has been developed by…, Type URH, —ultra rapid hardening, for use where ultra high early strength is desired;, Type VRH, —very rapid hardening, for use where very high early strength is desired;, Type MRH, —medium rapid hardening, for use where mid-range rapid hardening, high early strength is desired; and, Type GRH, —general rapid hardening, for use when the higher strength properties of Type VRH or a Type MRH cement is not required. “ASTM C1600 lists minimum requirements for compressive strength, setting time, shrinkage and soundness (autoclave expansion),” says Hicks. “Optional specifications for sulfate expansion, alkali silicate reactions with aggregates, heat of hydration and expansion in water are also…
-
Those involved in the rehabilitation of pressurized piping systems are invited to participate in the development of a proposed new standard, ASTM WK24231 , Practice/Guide for Internal Pipe Epoxy Barrier Coating Material Used in Pressurized Piping Systems. The proposed standard is being developed by Subcommittee F17.67 on Trenchless Plastic Pipeline Technology, part of ASTM International Committee…
-
ASTM International Committee F17 on Plastic Piping Systems is currently developing an efficient means to standardize fabricated polyvinyl chloride pressure fittings that are used in a variety of piping applications. The proposed new standard, WK23931 , Specification for Fabricated PVC Pressure Fittings, is under the jurisdiction of Subcommittee F17.10 on Fittings. Some of the applications that…
-
Thermoplastic corrugated stormwater chambers are similar to other types of plastic piping systems in that they are subjected to significant live loads from surface traffic as well as dead loads from earth cover. However, differences in construction — specifically, the fact that chambers are open-bottomed arches — necessitate an understanding of how corrugated stormwater chambers behave…
-
A proposed new standard that will allow for the joining of copper and plastic piping materials is currently being developed by ASTM International Committee F17 on Plastic Piping Systems. The proposed standard, WK21656 , Specification for Structural Adhesive for Bonding Similar and Dissimilar Piping Materials, is under the jurisdiction of Subcommittee F17.20 on Joining. “ WK21656 is the result of…
-
A proposed new standard under the jurisdiction of ASTM International Committee F17 on Plastic Piping Systems will be useful to the gas gathering and distribution industries. Subcommittee F17.11 on Composite is developing the proposed standard, WK21276 , Specification for Polyethylene Pipe with a Co-Extruded Polyamide Inner and/or Outer Barrier Layer for Oil and Gas Applications. According to…
-
Installers of plumbing systems using PEX and PE-RT polyethylene pipe will be the primary users of a new ASTM International standard approved by Committee F17 on Plastic Piping Systems. The new standard, ASTM F2735 , Specification for Plastic Insert Fittings for SDR9 Cross-Linked Polyethylene (PEX) and Polyethylene of Raised Temperature (PE-RT) Tubing, is under the jurisdiction of Subcommittee F17…
-
A proposed new ASTM International standard, WK19571 , Practice for Requirements for New Pipe and Fitting Materials for Gas Distribution Systems, will give the natural gas industry an important tool and defined process in continuing research and development efforts that will lead to the streamlined introduction of innovative products for the gas distribution industry. ASTM WK19571 is under the…
-
A proposed new ASTM International standard will facilitate more efficient recycling of a variety of post-consumer plastics. The proposed standard, WK20632, Practice for Marking Plastic Products for Identification in Reuse and Recycling, is under the jurisdiction of Subcommittee D20.95 on Recycled Plastics, part of ASTM International Committee D20 on Plastics. ASTM WK20632 is based on an original…
-
All interested parties are welcome to join in the standards developing activities of ASTM International Committee D20 on Plastics. Current D20 projects such as the development of proposed new standards covering backed vinyl siding and bioreactor landfill conditions demonstrate the diversity of D20’s work., Backed Vinyl Siding, Subcommittee D20.24 on Plastic Building Products is developing WK18425 , Specification for Rigid Poly (Vinyl Chloride) (PVC) Siding with Foam Plastic Backing (Backed Vinyl Siding). Vinyl siding with an integral foam plastic backing has been commercially available for nearly a decade. Because backed-vinyl siding is a variation of the basic siding product, testing and third party certification for…, Biodegradability of Plastics in Landfill Conditions, A proposed new standard being developed by Subcommittee D20.96 on Environmentally Degradable Plastics and Biobased Products will aid in the determination of degradation and biodegradation of plastics in landfill environments. All interested parties are encouraged to participate in the development of WK18427 , Determining the Aerobic Degradation and Anaerobic Biodegration of Plastic Materials…