Search
Advanced search
Filter by category
Filter by committee
Search results
-
A new ASTM International standard will help gasket manufacturers test to see how their products handle various compressions and loads. The test method shows the compression properties of a gasket by measuring its deflection while subjected to an increasing load. ASTM International member Jim Lingenfelder says that the test can provide information at both ambient and elevated temperatures, helping…
-
Recent changes in technology are now covered in a significant ASTM International standard used to measure the particle size of metal powders. The standard, ASTM B330 , Test Methods for Estimating Average Particle Size of Metal Powders and Related Compounds Using Air Permeability, is under the jurisdiction of Subcommittee B09.03 on Refractory Metal Powders , part of ASTM International Committee…, ASTM Committee B09 Next Meeting:, April 14-16, 2014, Hollywood, Fla., Technical Contact:, Frank Venskytis, Clayton, N.C., Phone: 919-553-8050; fvastm@embarqmail.com , ASTM Staff Contact:, Katerina Koperna, Phone: 610-832-9728; kkoperna@astm.org, ASTM PR Contact:, Barbara Schindler, Phone: 610-832-9603; bschindl@astm.org Release #9544
-
A new ASTM International standard will provide gasket manufacturers a test for measuring creep and compression that can be used for R&D and material comparisons, and as a quality assurance tool. ASTM F2837 , Test Method for Hot Compression Properties of Gasket Materials, was developed by Subcommittee F03.40 on Chemical Test Methods, under the jurisdiction of ASTM International Committee F03…, ASTM Committee F03 Next Meeting:, Oct 12-13, October Committee Week, San Antonio, Texas, Technical Contact:, James Lingenfelder, Gasket Resources Inc., Houston, Texas, Phone: 713-856-9445; jtling@durlon.com, ASTM Staff Contact:, Joseph Hugo, Phone: 610-832-9740; jhugo@astm.org, ASTM PR Contact:, Barbara Schindler, Phone: 610-832-9603; bschindl@astm.org Release #8695/Sept2010
-
Flow characteristics of fine metal powders are important in filling dies for pressing of powder metallurgy compacts, which are later sintered and sometimes machined into finished parts. The flow rate, as measured by a new ASTM standard, determines the flow necessary for a precise quantity of powder to be introduced into the die. The new standard, B964 , Test Methods for Flow Rate of Metal Powders…
-
Two recently approved ASTM International standards provide user-friendly tests for properties of sintered metallurgy products. The new standards, developed by Subcommittee B09.04 on Bearings, are ASTM B962 , Test Methods for Density of Compacted or Sintered Power Metallurgy (PM) Products Using Archimedes’ Principle, and ASTM B963 , Test Methods for Oil Content, Oil-Impregnation Efficiency and…
-
No industry standard currently exists that addresses the vacuum sealing requirements of knife-edged flanges for high vacuum applications. Existing international standards focus on interchangeability of the hardware, but do not address the reliability of the seal. ASTM International Committee E42 on Surface Analysis is now working on a proposed standard on the subject, WK21206 , Specification…
-
A 2002 workshop on galling wear held by ASTM International Committee G02 on Wear and Erosion provided the impetus for the development of a new standard, ASTM G196 , Test Method for Galling Resistance of Material Couples. The new standard is under the jurisdiction of Subcommittee G02.40 on Non-Abrasive Wear. According to Scott Hummel, Ph.D., associate professor, head of the department of…
-
ASTM International Committee F03 on Gaskets has developed and approved a new standard that can be used to evaluate gasket materials covered by ASTM F104 , Classification System for Nonmetallic Gasket Materials. The new standard, F2716 , Practice for Comparison of Nonmetallic Flat Gaskets in High Pressure Saturated Steam, is under the jurisdiction of Subcommittee F03.10 on Composite Gaskets. ASTM…
-
A new ASTM International standard responds to a recent emphasis by regulatory agencies that firms manufacturing drug products demonstrate the efficacy of disinfectants used in controlled environments. The standard, ASTM E2614 , Guide for Evaluation of Cleanroom Disinfectants, was developed by Subcommittee E35.15 on Antimicrobial Agents, part of ASTM International Committee E35 on Pesticides and…
-
A proposed new standard being developed by ASTM International Committee B09 on Metal Powders and Metal Powder Products offers a solution to the challenge of handling and characterizing very fine powders. Subcommittee B09.02 on Base Metal Powders is developing the proposed standard, WK13023 , Test Method for Determination of Tap Density of Metallic Powders by a Constant Volume Measuring Method. …